LumberJocks

woodman71's Favorites

  • Advertise with us
View jfk4032's profile

Tumbling block cutting board techniques, lessons learned and tips for cutting and assembly

01-13-2014 02:32 PM by jfk4032 | 13 comments »

After looking through some other blogs here on LJ and watching some Youtube videos I thought that the tumbling block cutting board was something that looked challenging, cool and something I wanted to try. I learned some good ideas from these other blogs and wanted to share some of my experiences having now made three of these, my setbacks and discoveries to better produce these tumbling block patterns. I purchased a Wixey digital angle gauge as it looked like you really needed to be accu...

Read this entry »


View Philzoel's profile

my first falling blocks #1: my first tumbling blocks

01-18-2012 12:14 AM by Philzoel | 6 comments »

Started this project in early Jan when i saw them by degoose. Made this drawing immediately to see if I could figure the angles. 60 degrees () to make 6 sided figure was the clue. 360/6 = 60. Took me awhile and drawing the box in bottom right of this drawing. Next hurdle was how much wood of each type (color)? In The drawing top middle, shows board 1.6” thick. Cut on 60 with all sides equal to hypotenuse. in this cause sine 60 = 1.6/x or x= 1.85”. all sides need...

Read this entry »


View poroskywood's profile

Drunken Cutting Boards #1: Drunken Alice in Wonderland Cutting Board

09-10-2009 03:22 AM by poroskywood | 52 comments »

Hey everybody, after a few personal messages here is my version of a how to on a Drunken Checker Board. I of coarse bow to the Chairman of the Board and pay tribute with beer. This is a Off-Checker pattern I call “Drunken Alice in Wonderland” The “serendipitous” nature of this piece is appealing in a far out sort of way. Here Goes… So first I prepare the Material. I am using Hard Maple and Walnut both are surfaced flat and cut 1” x 9” x 14&...

Read this entry »


View degoose's profile

Glue up of a woven board..

05-17-2009 10:31 AM by degoose | 19 comments »

This is just a little tip.. not the whole tutorial of how to cut and make a woven board.Basically you all can make the weave with the two accent stripes on each side.. right.[ ok just a length of the main timber with 2 stripes cut 1/16 or 1/8 ” thick and glued up. see the pics and work it out ]You can also make the background pieces from the other of the accent timbers the same width as the main weave less the accents.. ok so far.. so I don’t need to go though all that do I? PM m...

Read this entry »


View degoose's profile

How to make a endgrain tumbling block butcher block board!

08-12-2009 12:13 PM by degoose | 57 comments »

Hi guys ,, I had a request to make a tutorial with regards the endgrain Tumbling Block Design.First off,.., You need to decide the size of the blocks…. for this example I used 1” stock… Or something similar.. actually just over .. once dressed. Set the blade of the table saw to 60 degrees.. a bevel box makes this simpleI use the INCRA fence system so it is easy to rip bevels off side of the blade.Once the bevels are ripped measure the length of the bevel and move the f...

Read this entry »


View Tony's profile

Lattice Cutting board Help

09-11-2007 03:45 PM by Tony | 31 comments »

Update: 7 september 2010. As I do not have a lot of spare time for woodworking at the moment, I am submitting this blog for the contest, I hope you guys don’t mind that it is a little old Here is a link to the final projects- http://lumberjocks.com/projects/2542http://lumberjocks.com/projects/2559 http://lumberjocks.com/assets/pictures/projects/9436-438x.jpg?1233630507 After several e-mails requesting the plans for the Dan Walters cutting board I copied I decided to put some...

Read this entry »



DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com