Woodworking forum topics tagged with 'hand tools'

  • Advertise with us
All Topics Replies Last post
View andyperez's profile

Jointing End Grain of Large Panel

12-20-2021 05:55 PM by andyperez in Hand Tools

Hi everyone! I’m still relatively new to woodworking with only a cou...

5 12-21-2021 03:40 PM
View DevinT's profile

Dem-Bart Checkering Tool Kit

10-20-2021 08:55 PM by DevinT in Hand Tools

I can’t remember why I was researching how to do this by hand, but I re...

19 10-24-2021 12:52 PM
View Brad's profile

Workbench Tool Well? Yes or no and why.

11-25-2012 04:17 PM by Brad in Hand Tools

Hi Guys and Gals, I’ve been toying with idea of adding a tool well t...

67 10-16-2021 06:11 PM
View tomsoyer1's profile

Stanley Hand Drill No. 624 - $20

07-26-2021 10:57 AM by tomsoyer1 in Woodworking Trade & Swap

Stanley hand Drill. Good condition 20$ O BO. I have other hand tools that ...

0 07-26-2021 10:57 AM
View MJHaffeman's profile

Tool identification

06-25-2021 07:50 PM by MJHaffeman in Hand Tools

I just finished building my house, largely by myself, and while cleaning up a...

84 07-22-2021 03:05 PM
View BigMig's profile

Successfully Selecting Sapele and Birdseye Maple in Rough Boards

06-04-2021 02:48 PM by BigMig in Woodworking Skill Share

I’m beginning the planning stage of making a small-ish table for my ent...

5 06-04-2021 04:48 PM
View kiwilynne's profile

For the hand plane experts - Stanley & Record Production Eras?

05-17-2021 09:00 AM by kiwilynne in Hand Tools

I’ve become slightly…obsessed with hand planes. Two new acquis...

12 05-19-2021 01:43 AM
View kiwilynne's profile

Stanley bullnose?

05-10-2021 12:46 AM by kiwilynne in Hand Tools

I was recently given this little cutie by someone who had no idea where it ca...

4 05-10-2021 03:05 AM
View Jwinn's profile

Seeking advice on foot powered lathe design (treadle vs pedal)

04-11-2021 11:46 AM by Jwinn in Woodturning

I recently got an old lathe from a relative (ways/bed, 3 speed belt driven he...

2 04-23-2021 03:22 AM
View need2boat's profile

A.A. Woods & Sons spoke pointers and hollow auger

10-18-2011 07:29 PM by need2boat in Hand Tools

Lets keeping this simple. ;-) I’ve got one and looking to use it in ...

4 04-02-2021 04:07 PM
View Francisco Luna's profile


02-06-2021 08:46 PM by Francisco Luna in Hand Tools

I was about to shot for a $140 Lie Nielsen Dovetail saw, but then I was think...

13 02-09-2021 02:36 PM
View Olivepress's profile

(closed) Lie-Nielsen No. 102 Iron Low Angle Block Plane L-N 102 - SOLD

01-26-2021 06:45 PM by Olivepress in Hand Tools

I’m looking to sell my Lie-Nielsen No. 102 Iron Low Angle Block Plane. I&#...

9 02-02-2021 11:59 PM
View bugradx2's profile

Favorite stocking stuffers?

12-14-2020 10:39 PM by bugradx2 in Hand Tools

I have a nephew who has most of the major tools but not much for smaller type...

15 12-16-2020 04:12 PM
View jayseedub's profile

What's Your Favorite (Affordable) Screwdriver Set?

09-08-2020 06:58 PM by jayseedub in Hand Tools

What’s your favorite mass-produced screwdriver set? I’m in the ...

32 10-19-2020 06:47 PM
View AGolden's profile

plow plane groove distance from edge

08-27-2020 05:55 PM by AGolden in Hand Tools

Hello All, I have been thinking of making some shorter rails for my stanle...

7 08-27-2020 10:46 PM
View JasonIndy's profile

Handsaw service in Indianapolis area?

05-22-2020 12:56 PM by JasonIndy in Hand Tools

Hey folks, I have not had much luck online but I have a few older saws I am l...

4 06-10-2020 08:30 PM
View DoctorHandtool's profile

Hello sorry if this is the wrong forum Introduction only post in hantools

06-05-2020 01:07 AM by DoctorHandtool in Hand Tools

Hi, just got back to the restoration and old tool game. In my past I would tu...

19 06-06-2020 01:49 AM
View Nick3253's profile

First Hand Plane

05-15-2020 02:13 PM by Nick3253 in Hand Tools

Hello, I just got my first hand planes, I’ve been woodworking f...

7 05-15-2020 09:35 PM
View livewire516's profile

Is this an Atlas 120? Help me identify this ol' Disston

04-07-2020 03:15 AM by livewire516 in Hand Tools

One this I should make clear: I salvaged that medallion from another saw....

6 04-07-2020 08:51 PM
View Don Broussard's profile

Stanley No. 45 Cutters

07-05-2013 02:29 PM by Don Broussard in Woodworking Trade & Swap

Does any LJ have an “extra” set of Stanley No. 45 cutters they...

23 03-27-2020 02:16 PM

1 2 3 4 ... 11 next »
205 topics

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics