LumberJocks

Delta saw arbor nut source

  • Advertise with us

« back to Power Tools, Hardware and Accessories forum

Forum topic by spkwms posted 09-11-2020 06:44 AM 450 views 0 times favorited 11 replies Add to Favorites Watch
View spkwms's profile

spkwms

14 posts in 3669 days


09-11-2020 06:44 AM

Topic tags/keywords: tablesaw

I need an arbor nut for a Delta model 36-714 10 inch table saw. The nut part number is A06325. Delta says not available and no recommended replacement. The nut is for a LH tilt RH threaded arbor.

I am open to all suggestions as to where I can get a replacement.

Thank you


11 replies so far

View LittleBlackDuck's profile (online now)

LittleBlackDuck

5795 posts in 1703 days


#1 posted 09-11-2020 09:24 AM

Sounds like my arbor nut issue a few years back… the chances are it’s an acme thread and not readily available over the counter. If Delta can’t help, you’ll be sharpening that pointed stick, moving the TP aside, while looking up that steep hill.

I had a similar issue and started spruiking recycled table saw vendors after the original vendor gave me the no can help sales pitch… After wasting a few months and getting nowhere fast I bit the bullet and took the nut to an engineer and got them to make up a couple for me. The first cost me over $50 but the remaining 3 cost an additional $1.50 (for the three)... Fortunately in my original queries I got a response from another bunny faced with a similar predicament and he was prepared to split the cost for two of them… I deliberately got more than 1 as I had to file a nut down to accomodate my dado set and I’d rather have spares than pay for initial tooling again if required. The fact that I needed a nut to file down and still had the original kept the urgency at bay.
If it is an acme thread it may be a “standard size” that could be canibalised from other branded machinery… I suppose it just depends on how desperate you are. If I amortised the original $50 over the time I spent/wasted searching, it’d work out to be around a few bucks per hour… which I thought was a fair trade… and the cost split between two desperados just sweetened the expense.

-- If your first cut is too short... Take the second cut from the longer end... LBD

View SAndelin's profile

SAndelin

12 posts in 3854 days


#2 posted 09-11-2020 03:23 PM

Here are a couple of threads about the Delta arbor nut. I bought a couple of the brass Uninuts made by a guy who frequents OWWM, and those are very high quality. IIRC those look like ACME threads but are some other industrial thread type that is “close” to the same dimensions of ACME threads, but not the same.

https://www.lumberjocks.com/replies/on/1481333
https://www.lumberjocks.com/topics/249226

Hope that helps.

-- Luck, the point where preparation meets opportunity.

View HerringImpaired's profile

HerringImpaired

80 posts in 592 days


#3 posted 09-11-2020 03:35 PM

Could this be the part. They list a 36-710, maybe the 36-714 is a revision of the 710?
Sorry if no help…. You said the part was no longer carried by Delta, but this source says that is where the parts were obtained….. Check the comments, it sounds like one person claims they replaced your part number with this part.

https://www.ereplacementparts.com/hex-nut-p-86309.html?gclid=Cj0KCQjwwOz6BRCgARIsAKEG4FX948M3ra5pLb2UvslStz3M8GbHrXMkf7M-XOEk57AUsGUF7CD0ZcoaAtw_EALw_wcB

-- "My greatest fear is that upon my demise, my wife will sell my tools for what I said I paid for them."

View 987Ron's profile

987Ron

104 posts in 199 days


#4 posted 09-11-2020 03:37 PM

The part number for the arbor nut is A06325. The following site says they have it in stock and ship in 5-7 days. Price $5.95 plus shipping. Did not check to see if it is actually available
https://www.appliancepartspros.com/delta-power-equipment-arbor-nut-a06325-ap6619287.html?msclkid=430206c5c6f61377f03c599e5e926007&utm_source=bing&utm_medium=cpc&utm_campaign=Campaign%20%23%20-%20Part%20Numbers&utm_term=Delta%20A06325&utm_content=016

The site is AppliancePartsPros.com never ordered or had any dealings with them. Hope this helps

-- It's not a mistake it's a design opportunity

View ibewjon's profile

ibewjon

2078 posts in 3676 days


#5 posted 09-11-2020 05:22 PM

I have purchased there many times. No problems.

View HerringImpaired's profile

HerringImpaired

80 posts in 592 days


#6 posted 09-11-2020 07:07 PM



The part number for the arbor nut is A06325. The following site says they have it in stock and ship in 5-7 days. Price $5.95 plus shipping. Did not check to see if it is actually available
https://www.appliancepartspros.com/delta-power-equipment-arbor-nut-a06325-ap6619287.html?msclkid=430206c5c6f61377f03c599e5e926007&utm_source=bing&utm_medium=cpc&utm_campaign=Campaign%20%23%20-%20Part%20Numbers&utm_term=Delta%20A06325&utm_content=016

The site is AppliancePartsPros.com never ordered or had any dealings with them. Hope this helps

- 987Ron

Site at the link says out of stock. Maybe the OP got the last one…..

-- "My greatest fear is that upon my demise, my wife will sell my tools for what I said I paid for them."

View spkwms's profile

spkwms

14 posts in 3669 days


#7 posted 09-11-2020 11:09 PM

Checked with AppliancePartsPros and they are out of stock and will not be restocking.

View LittleBlackDuck's profile (online now)

LittleBlackDuck

5795 posts in 1703 days


#8 posted 09-12-2020 12:35 AM



... IIRC those look like ACME threads but are some other industrial thread type that is “close” to the same dimensions of ACME threads, but not the same.
- SAndelin

Thanks SA... I stand (well actually sitting) corrected. I was informed that my nut (arbor) was acme and acme was fabricated and it fit…
Apologies if I mislead anyone… nothing worse than bad advice (and C19... and bad vino)...

-- If your first cut is too short... Take the second cut from the longer end... LBD

View unclearthur's profile

unclearthur

374 posts in 2670 days


#9 posted 09-12-2020 07:44 AM


Here are a couple of threads about the Delta arbor nut. I bought a couple of the brass Uninuts made by a guy who frequents OWWM, and those are very high quality. IIRC those look like ACME threads but are some other industrial thread type that is “close” to the same dimensions of ACME threads, but not the same.

https://www.lumberjocks.com/replies/on/1481333
https://www.lumberjocks.com/topics/249226

Hope that helps.

- SAndelin

I bought an arbor nut for a Delta contractor saw from the fellow (Frank S.) in the first thread maybe 5 years ago; worked perfectly.

View spkwms's profile

spkwms

14 posts in 3669 days


#10 posted 09-24-2020 01:08 AM

I just received from Frank S. a brass arbor nut for my Delta saw. Excellent quality and wok perfect. If anyone is in need of a RH or LH arbor nut for a Delta I would recommend Frank.

View BurlyBob's profile

BurlyBob

7946 posts in 3148 days


#11 posted 09-24-2020 02:59 PM

check Ereplacement parts. I’ve bought several things from there. Prices are ok and shipping is quite fast.

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com