Forum topic by Dave Polaschek | posted 05-06-2018 02:04 PM | 862 views | 0 times favorited | 13 replies | ![]() |
![]() |
05-06-2018 02:04 PM |
Topic tags/keywords: hand tool forensics Following up on Ron’s idea, here’s another photo. As in the past, See if you can identify the operation and hand tool that produced this waste. Akin to mechanisms of injury. Seeing an end result and determining the cause. -- Dave - Santa Fe |
13 replies so far
#1 posted 05-06-2018 02:25 PM |
Looks like chainsaw shaving from cutting a los with the grain -- Somewhere between raising hell and amazing grace. |
#2 posted 05-06-2018 02:45 PM |
looks like from a spokeshave …..chambering corners ? :<)) -- Tony---- Reinholds,Pa.------ REMEMBER TO ALWAYS HAVE FUN :<)) |
#3 posted 05-06-2018 02:50 PM |
Hand-tools, Craig. Tony, close but no cigar. -- Dave - Santa Fe |
#4 posted 05-06-2018 02:55 PM |
it looks like a scraper, the sort I get cleaning up a round -- nice recovery, They should pay extra for that mistake, Eric E. |
#5 posted 05-06-2018 02:59 PM |
Block plane easing the corners on your box :) -- Bill, Yo!......in Brooklyn & Steel City :) |
#6 posted 05-06-2018 02:59 PM |
Not a scraper, Eric. -- Dave - Santa Fe |
#7 posted 05-06-2018 03:00 PM |
Not easing corners, Bill. Nor chamfering. -- Dave - Santa Fe |
#8 posted 05-06-2018 03:04 PM |
I have seen shavings like that, removing bark from a green sapling. Done with a butter knife -- nice recovery, They should pay extra for that mistake, Eric E. |
#9 posted 05-06-2018 03:23 PM |
From cutting grooves, or dados with a plough plane. -- You can lead a horse to water, but you can't tie his shoes. Blaze Foley |
#10 posted 05-06-2018 03:37 PM |
Eric got close enough. It’s cleaning up the edge of a piece of 1/4” Baltic birch plywood with a jack plane (set to about 1/64” per pass – I routinely cut plywood 1/4” from the line, then plane down to the line, aiming for about 20 passes to get there). The ragged edges on the wood shavings (from the cross-grain plies, that I’m planing off the end grain) are what make it look different from chamfering or peeling bark or other operations on solid wood. -- Dave - Santa Fe |
#11 posted 05-06-2018 06:39 PM |
Ha! I was going to guess you had sharpened your scratch stock tool -- "Duck and Bob would be out doin some farming with funny hats on." chrisstef |
#12 posted 05-06-2018 11:15 PM |
That makes much shorter curls, Duck. But yeah, the edges are similarly raggedy. Maybe that’ll be the next challenge. ;-) -- Dave - Santa Fe |
#13 posted 05-06-2018 11:26 PM |
Usually get those shavings from my Stanley 45…...ploughing grooves. -- A Planer? I'M the planer, this is what I use |
Have your say...
You must be signed in to reply.
|
Forum | Topics |
---|---|
Woodworking Skill Share
|
13147 |
Woodturning
|
2788 |
Woodcarving
|
565 |
Scrollsawing
|
414 |
Joinery
|
1872 |
Finishing
|
6304 |
Designing Woodworking Projects
|
7862 |
Power Tools, Hardware and Accessories
|
32559 |
CNC Woodworking
|
325 |
Hand Tools
|
6430 |
Jigs & Fixtures
|
1788 |
Wood & Lumber
|
7245 |
Safety in the Woodworking Shop
|
1614 |
Focus on the Workspace
|
2618 |
Sweating for Bucks Through Woodworking
|
1267 |
Woodworking Trade & Swap
|
5396 |
LumberJocks.com Site Feedback
|
2394 |
Coffee Lounge
|
9630 |