[Brad_Nailor]

An Hour Here, a Half-Hour There and a Few Saturday Mornings

Over the past month I found very little contiguous time to make progress on the shop setup. Consequently I never felt like I had made significant enough progress in any given week to warrant a new post. While I'm still quite some distance from the finish line, I finally feel like I can actually say, once again, "I have a shop!"



Dust Collection Controls

I installed a half-dozen doorbell buttons around the shop, under bench tops near power tools, on the wall by the bandsaw and underneath the tablesaw fence next to the power switch. I installed a couple power outlets in the crawl space under the shop for the controller as well as my air compressor which I located in a corner of the crawl. I also programmed the air filter as I discussed in my last post to automatically switch on with the dust collector and off 2 minutes after the collector is switched off. I'm extremely pleased with how this has worked out.



Supplies Organized & Remaining Tools Installed

I finally managed to commit to drawer assignments for my tools and supplies. For the most part the drawers are logically organized, though a few of them are temporary "catch-alls" waiting for the day when I complete the upper cabinets. I enlisted the aid of my brother, sister-in-law and nephew to help wheel the 17" Grizzly bandsaw up a ramp and into the shop. This turned out to be not as difficult as I'd feared it would be. I also unboxed the Ridgid oscillating sander I'd purchased nearly 3 months ago and connected both to the dust collection drops installed previously. All the tools are in!



Clamp Racks

Following some quick research at my favorite site, I assembled and mounted some clamp racks for my rather modest pipe, parallel and bar clamp collection. I still have a number of spring and "C" clamps to hang, but I'm satisfied with the arrangement for now.



A Number of Tasks Remain

No matter how much I manage to accomplish, the list never really seems to get any shorter. Some tasks that remain are setting up dust collection for my router table and building an overarm blade guard for the table saw. The router table will require installing some kind of enclosure around the hanging router…which will take some time to devise. I'm also working on a design for a tall thin "drawer" to fill the 2 spaces in the RAS cabinet. These opening are roughly 36" tall by only 9" wide. I'm thinking that I'll create a sliding angled vertical panels in one to hold router bits and a vertical pull-out panel in the other for miter/RAS/table/circular saw blade storage. Next steps also include major improvements to the "large piece assembly area"-which my wife insists upon calling a "garage." Improvements include an updated lumber rack and sheet goods pen as well as some custom cabinets for "non-wood-related" storage…though I can't imagine what that might be.



The bottom line is that I'm just about ready to get back to spending at least some time working "in" the shop instead of "on" the shop! Hooray!

(Originally Posted at http://tenonandspline.com/blog/archives/75)

Now taking a second look, is there a skylight or are they just lights? Doah!

 

[pjaromin]

An Hour Here, a Half-Hour There and a Few Saturday Mornings

Over the past month I found very little contiguous time to make progress on the shop setup. Consequently I never felt like I had made significant enough progress in any given week to warrant a new post. While I'm still quite some distance from the finish line, I finally feel like I can actually say, once again, "I have a shop!"



Dust Collection Controls

I installed a half-dozen doorbell buttons around the shop, under bench tops near power tools, on the wall by the bandsaw and underneath the tablesaw fence next to the power switch. I installed a couple power outlets in the crawl space under the shop for the controller as well as my air compressor which I located in a corner of the crawl. I also programmed the air filter as I discussed in my last post to automatically switch on with the dust collector and off 2 minutes after the collector is switched off. I'm extremely pleased with how this has worked out.



Supplies Organized & Remaining Tools Installed

I finally managed to commit to drawer assignments for my tools and supplies. For the most part the drawers are logically organized, though a few of them are temporary "catch-alls" waiting for the day when I complete the upper cabinets. I enlisted the aid of my brother, sister-in-law and nephew to help wheel the 17" Grizzly bandsaw up a ramp and into the shop. This turned out to be not as difficult as I'd feared it would be. I also unboxed the Ridgid oscillating sander I'd purchased nearly 3 months ago and connected both to the dust collection drops installed previously. All the tools are in!



Clamp Racks

Following some quick research at my favorite site, I assembled and mounted some clamp racks for my rather modest pipe, parallel and bar clamp collection. I still have a number of spring and "C" clamps to hang, but I'm satisfied with the arrangement for now.



A Number of Tasks Remain

No matter how much I manage to accomplish, the list never really seems to get any shorter. Some tasks that remain are setting up dust collection for my router table and building an overarm blade guard for the table saw. The router table will require installing some kind of enclosure around the hanging router…which will take some time to devise. I'm also working on a design for a tall thin "drawer" to fill the 2 spaces in the RAS cabinet. These opening are roughly 36" tall by only 9" wide. I'm thinking that I'll create a sliding angled vertical panels in one to hold router bits and a vertical pull-out panel in the other for miter/RAS/table/circular saw blade storage. Next steps also include major improvements to the "large piece assembly area"-which my wife insists upon calling a "garage." Improvements include an updated lumber rack and sheet goods pen as well as some custom cabinets for "non-wood-related" storage…though I can't imagine what that might be.



The bottom line is that I'm just about ready to get back to spending at least some time working "in" the shop instead of "on" the shop! Hooray!

(Originally Posted at http://tenonandspline.com/blog/archives/75)

David - You were correct the first time.

There are 2 skylights with light fixtures around/between them.

 

[Freddo]

An Hour Here, a Half-Hour There and a Few Saturday Mornings

Over the past month I found very little contiguous time to make progress on the shop setup. Consequently I never felt like I had made significant enough progress in any given week to warrant a new post. While I'm still quite some distance from the finish line, I finally feel like I can actually say, once again, "I have a shop!"



Dust Collection Controls

I installed a half-dozen doorbell buttons around the shop, under bench tops near power tools, on the wall by the bandsaw and underneath the tablesaw fence next to the power switch. I installed a couple power outlets in the crawl space under the shop for the controller as well as my air compressor which I located in a corner of the crawl. I also programmed the air filter as I discussed in my last post to automatically switch on with the dust collector and off 2 minutes after the collector is switched off. I'm extremely pleased with how this has worked out.



Supplies Organized & Remaining Tools Installed

I finally managed to commit to drawer assignments for my tools and supplies. For the most part the drawers are logically organized, though a few of them are temporary "catch-alls" waiting for the day when I complete the upper cabinets. I enlisted the aid of my brother, sister-in-law and nephew to help wheel the 17" Grizzly bandsaw up a ramp and into the shop. This turned out to be not as difficult as I'd feared it would be. I also unboxed the Ridgid oscillating sander I'd purchased nearly 3 months ago and connected both to the dust collection drops installed previously. All the tools are in!



Clamp Racks

Following some quick research at my favorite site, I assembled and mounted some clamp racks for my rather modest pipe, parallel and bar clamp collection. I still have a number of spring and "C" clamps to hang, but I'm satisfied with the arrangement for now.



A Number of Tasks Remain

No matter how much I manage to accomplish, the list never really seems to get any shorter. Some tasks that remain are setting up dust collection for my router table and building an overarm blade guard for the table saw. The router table will require installing some kind of enclosure around the hanging router…which will take some time to devise. I'm also working on a design for a tall thin "drawer" to fill the 2 spaces in the RAS cabinet. These opening are roughly 36" tall by only 9" wide. I'm thinking that I'll create a sliding angled vertical panels in one to hold router bits and a vertical pull-out panel in the other for miter/RAS/table/circular saw blade storage. Next steps also include major improvements to the "large piece assembly area"-which my wife insists upon calling a "garage." Improvements include an updated lumber rack and sheet goods pen as well as some custom cabinets for "non-wood-related" storage…though I can't imagine what that might be.



The bottom line is that I'm just about ready to get back to spending at least some time working "in" the shop instead of "on" the shop! Hooray!

(Originally Posted at http://tenonandspline.com/blog/archives/75)

There's a bit of heaven on earth! Nice walls - so inviting and warm feeling with the natural light coming in. Enjoy your space!

 

[Sung]

An Hour Here, a Half-Hour There and a Few Saturday Mornings

Over the past month I found very little contiguous time to make progress on the shop setup. Consequently I never felt like I had made significant enough progress in any given week to warrant a new post. While I'm still quite some distance from the finish line, I finally feel like I can actually say, once again, "I have a shop!"



Dust Collection Controls

I installed a half-dozen doorbell buttons around the shop, under bench tops near power tools, on the wall by the bandsaw and underneath the tablesaw fence next to the power switch. I installed a couple power outlets in the crawl space under the shop for the controller as well as my air compressor which I located in a corner of the crawl. I also programmed the air filter as I discussed in my last post to automatically switch on with the dust collector and off 2 minutes after the collector is switched off. I'm extremely pleased with how this has worked out.



Supplies Organized & Remaining Tools Installed

I finally managed to commit to drawer assignments for my tools and supplies. For the most part the drawers are logically organized, though a few of them are temporary "catch-alls" waiting for the day when I complete the upper cabinets. I enlisted the aid of my brother, sister-in-law and nephew to help wheel the 17" Grizzly bandsaw up a ramp and into the shop. This turned out to be not as difficult as I'd feared it would be. I also unboxed the Ridgid oscillating sander I'd purchased nearly 3 months ago and connected both to the dust collection drops installed previously. All the tools are in!



Clamp Racks

Following some quick research at my favorite site, I assembled and mounted some clamp racks for my rather modest pipe, parallel and bar clamp collection. I still have a number of spring and "C" clamps to hang, but I'm satisfied with the arrangement for now.



A Number of Tasks Remain

No matter how much I manage to accomplish, the list never really seems to get any shorter. Some tasks that remain are setting up dust collection for my router table and building an overarm blade guard for the table saw. The router table will require installing some kind of enclosure around the hanging router…which will take some time to devise. I'm also working on a design for a tall thin "drawer" to fill the 2 spaces in the RAS cabinet. These opening are roughly 36" tall by only 9" wide. I'm thinking that I'll create a sliding angled vertical panels in one to hold router bits and a vertical pull-out panel in the other for miter/RAS/table/circular saw blade storage. Next steps also include major improvements to the "large piece assembly area"-which my wife insists upon calling a "garage." Improvements include an updated lumber rack and sheet goods pen as well as some custom cabinets for "non-wood-related" storage…though I can't imagine what that might be.



The bottom line is that I'm just about ready to get back to spending at least some time working "in" the shop instead of "on" the shop! Hooray!

(Originally Posted at http://tenonandspline.com/blog/archives/75)

nice work. i could learn a thing or two from your set up.

 

[SCOTSMAN]

An Hour Here, a Half-Hour There and a Few Saturday Mornings

Over the past month I found very little contiguous time to make progress on the shop setup. Consequently I never felt like I had made significant enough progress in any given week to warrant a new post. While I'm still quite some distance from the finish line, I finally feel like I can actually say, once again, "I have a shop!"



Dust Collection Controls

I installed a half-dozen doorbell buttons around the shop, under bench tops near power tools, on the wall by the bandsaw and underneath the tablesaw fence next to the power switch. I installed a couple power outlets in the crawl space under the shop for the controller as well as my air compressor which I located in a corner of the crawl. I also programmed the air filter as I discussed in my last post to automatically switch on with the dust collector and off 2 minutes after the collector is switched off. I'm extremely pleased with how this has worked out.



Supplies Organized & Remaining Tools Installed

I finally managed to commit to drawer assignments for my tools and supplies. For the most part the drawers are logically organized, though a few of them are temporary "catch-alls" waiting for the day when I complete the upper cabinets. I enlisted the aid of my brother, sister-in-law and nephew to help wheel the 17" Grizzly bandsaw up a ramp and into the shop. This turned out to be not as difficult as I'd feared it would be. I also unboxed the Ridgid oscillating sander I'd purchased nearly 3 months ago and connected both to the dust collection drops installed previously. All the tools are in!



Clamp Racks

Following some quick research at my favorite site, I assembled and mounted some clamp racks for my rather modest pipe, parallel and bar clamp collection. I still have a number of spring and "C" clamps to hang, but I'm satisfied with the arrangement for now.



A Number of Tasks Remain

No matter how much I manage to accomplish, the list never really seems to get any shorter. Some tasks that remain are setting up dust collection for my router table and building an overarm blade guard for the table saw. The router table will require installing some kind of enclosure around the hanging router…which will take some time to devise. I'm also working on a design for a tall thin "drawer" to fill the 2 spaces in the RAS cabinet. These opening are roughly 36" tall by only 9" wide. I'm thinking that I'll create a sliding angled vertical panels in one to hold router bits and a vertical pull-out panel in the other for miter/RAS/table/circular saw blade storage. Next steps also include major improvements to the "large piece assembly area"-which my wife insists upon calling a "garage." Improvements include an updated lumber rack and sheet goods pen as well as some custom cabinets for "non-wood-related" storage…though I can't imagine what that might be.



The bottom line is that I'm just about ready to get back to spending at least some time working "in" the shop instead of "on" the shop! Hooray!

(Originally Posted at http://tenonandspline.com/blog/archives/75)

This is too good for the human eyes LOL well done you deserve all you have as you've worked hard on this may you and your family have a great lifetimes worth of enjoyment from your shop God Bless Alistair

 

[pjaromin]

Shop Air, and Sheet Goods Get A Home

My original design for the shop included multiple compressed air outlets scattered about the shop. At the heart of this system would be a 60gal Ingersol-Rand 2-stage compressor providing at least 15 [email protected] Now months later, I've significantly revised and downgraded my plans. Part of it was financial, but most of it was a realization that all that I really needed was to be able to use my nail guns without the hassle of dragging out the compressor every time and tripping over hose.

Retractable Air Hose

To that end, I revised my plans and settled on a much simpler setup. I would put my existing 17gal Husky in the crawlspace below the shop, and run a hose through the floor next to my main assembly table. To this I would attach a combination regulator/filter/oiler and a retractable hose. This is precisely what I did.



The air filter/oiler unit is a $20 special from Harbor Freight...well, I got it for $20. It was down to $15 last time I checked…sigh. Unfortunately it only occurred to me after I had purchased the filter unit that I don't really want an oiler. While most of the time I'll be using a nail gun, I do occasionally wish to use the air hose to blow off the shavings from a piece in progress and I doubt that misting it with tool oil would be very good for the finish. I've mounted the unit anyway and plan to keep the oiler empty. Perhaps someday I'll move this device to another location on a separate hose and reserve it specifically for tool use. Or maybe not.

The hose reel was $30 for 20ft. It was the cheapest I've seen and while not as "industrial" as some of the more expensive units, I kinda preferred the compact size and appearance of this one. It also included a swivel mount. It works great right now…hopefully the mechanism will prove more reliable than the price would imply. We'll see.

Automatic Drain Valve

Another Harbor Freight special. The plan was to locate the compressor in the crawl space, accessed via a trap door in the floor. Draining it regularly via the drain cock would be somewhat of a hassle. What I needed was an automatic drain. Thankfully I found this site in about 5 minutes of research pointing to a product from Harbor Freight. It was fairly straightforward to install-except that the inner diameter of the hose running from the unloader valve to the pressure switch on my compressor was too small for the included fittings. I ultimately wound up buying a different fitting which suffered from the same issue-but was setup in a such a way that I was able to coax the hose over the inner brass piece by applying a bit of heat. A bit of sanding of the outer tube was also required to get the connector attached to the tee. It was a bit of a chore, but ultimately I managed to get it all to work. And just like the author of the site above, my new drain cock valve was no good…so I also replaced it with a part from HD. The thing about the drain is that it only opens when the compressor starts and shuts off. So I can either leave the compressor on so that it "tops off" periodically (thereby activating the drain) or program the switch it's on (see my other posts re: Insteon) to run it for a few minutes each day and give it a chance to drain any condensation.



Vertical Sheet-goods Pen

Finally, after filling the compressor, I used my new hose and old air nailers to build a 9' tall x 30" wide x 36" deep vertical sheet goods pen just outside the shop door and install some cheap pre-primed moulding around the pen face and shop doors.

This is the start of my next big project: the Garage Remodel.

 

[GaryK]

Shop Air, and Sheet Goods Get A Home

My original design for the shop included multiple compressed air outlets scattered about the shop. At the heart of this system would be a 60gal Ingersol-Rand 2-stage compressor providing at least 15 [email protected] Now months later, I've significantly revised and downgraded my plans. Part of it was financial, but most of it was a realization that all that I really needed was to be able to use my nail guns without the hassle of dragging out the compressor every time and tripping over hose.

Retractable Air Hose

To that end, I revised my plans and settled on a much simpler setup. I would put my existing 17gal Husky in the crawlspace below the shop, and run a hose through the floor next to my main assembly table. To this I would attach a combination regulator/filter/oiler and a retractable hose. This is precisely what I did.



The air filter/oiler unit is a $20 special from Harbor Freight...well, I got it for $20. It was down to $15 last time I checked…sigh. Unfortunately it only occurred to me after I had purchased the filter unit that I don't really want an oiler. While most of the time I'll be using a nail gun, I do occasionally wish to use the air hose to blow off the shavings from a piece in progress and I doubt that misting it with tool oil would be very good for the finish. I've mounted the unit anyway and plan to keep the oiler empty. Perhaps someday I'll move this device to another location on a separate hose and reserve it specifically for tool use. Or maybe not.

The hose reel was $30 for 20ft. It was the cheapest I've seen and while not as "industrial" as some of the more expensive units, I kinda preferred the compact size and appearance of this one. It also included a swivel mount. It works great right now…hopefully the mechanism will prove more reliable than the price would imply. We'll see.

Automatic Drain Valve

Another Harbor Freight special. The plan was to locate the compressor in the crawl space, accessed via a trap door in the floor. Draining it regularly via the drain cock would be somewhat of a hassle. What I needed was an automatic drain. Thankfully I found this site in about 5 minutes of research pointing to a product from Harbor Freight. It was fairly straightforward to install-except that the inner diameter of the hose running from the unloader valve to the pressure switch on my compressor was too small for the included fittings. I ultimately wound up buying a different fitting which suffered from the same issue-but was setup in a such a way that I was able to coax the hose over the inner brass piece by applying a bit of heat. A bit of sanding of the outer tube was also required to get the connector attached to the tee. It was a bit of a chore, but ultimately I managed to get it all to work. And just like the author of the site above, my new drain cock valve was no good…so I also replaced it with a part from HD. The thing about the drain is that it only opens when the compressor starts and shuts off. So I can either leave the compressor on so that it "tops off" periodically (thereby activating the drain) or program the switch it's on (see my other posts re: Insteon) to run it for a few minutes each day and give it a chance to drain any condensation.



Vertical Sheet-goods Pen

Finally, after filling the compressor, I used my new hose and old air nailers to build a 9' tall x 30" wide x 36" deep vertical sheet goods pen just outside the shop door and install some cheap pre-primed moulding around the pen face and shop doors.

This is the start of my next big project: the Garage Remodel.

That's some good planning on the air!

 

[ND2ELK]

Shop Air, and Sheet Goods Get A Home

My original design for the shop included multiple compressed air outlets scattered about the shop. At the heart of this system would be a 60gal Ingersol-Rand 2-stage compressor providing at least 15 [email protected] Now months later, I've significantly revised and downgraded my plans. Part of it was financial, but most of it was a realization that all that I really needed was to be able to use my nail guns without the hassle of dragging out the compressor every time and tripping over hose.

Retractable Air Hose

To that end, I revised my plans and settled on a much simpler setup. I would put my existing 17gal Husky in the crawlspace below the shop, and run a hose through the floor next to my main assembly table. To this I would attach a combination regulator/filter/oiler and a retractable hose. This is precisely what I did.



The air filter/oiler unit is a $20 special from Harbor Freight...well, I got it for $20. It was down to $15 last time I checked…sigh. Unfortunately it only occurred to me after I had purchased the filter unit that I don't really want an oiler. While most of the time I'll be using a nail gun, I do occasionally wish to use the air hose to blow off the shavings from a piece in progress and I doubt that misting it with tool oil would be very good for the finish. I've mounted the unit anyway and plan to keep the oiler empty. Perhaps someday I'll move this device to another location on a separate hose and reserve it specifically for tool use. Or maybe not.

The hose reel was $30 for 20ft. It was the cheapest I've seen and while not as "industrial" as some of the more expensive units, I kinda preferred the compact size and appearance of this one. It also included a swivel mount. It works great right now…hopefully the mechanism will prove more reliable than the price would imply. We'll see.

Automatic Drain Valve

Another Harbor Freight special. The plan was to locate the compressor in the crawl space, accessed via a trap door in the floor. Draining it regularly via the drain cock would be somewhat of a hassle. What I needed was an automatic drain. Thankfully I found this site in about 5 minutes of research pointing to a product from Harbor Freight. It was fairly straightforward to install-except that the inner diameter of the hose running from the unloader valve to the pressure switch on my compressor was too small for the included fittings. I ultimately wound up buying a different fitting which suffered from the same issue-but was setup in a such a way that I was able to coax the hose over the inner brass piece by applying a bit of heat. A bit of sanding of the outer tube was also required to get the connector attached to the tee. It was a bit of a chore, but ultimately I managed to get it all to work. And just like the author of the site above, my new drain cock valve was no good…so I also replaced it with a part from HD. The thing about the drain is that it only opens when the compressor starts and shuts off. So I can either leave the compressor on so that it "tops off" periodically (thereby activating the drain) or program the switch it's on (see my other posts re: Insteon) to run it for a few minutes each day and give it a chance to drain any condensation.



Vertical Sheet-goods Pen

Finally, after filling the compressor, I used my new hose and old air nailers to build a 9' tall x 30" wide x 36" deep vertical sheet goods pen just outside the shop door and install some cheap pre-primed moulding around the pen face and shop doors.

This is the start of my next big project: the Garage Remodel.

Hi Patrick

Great idea on the air hook up. Looks like a slick set up. Thanks for posting.

God Bless
tom

 

[Tangle]

Shop Air, and Sheet Goods Get A Home

My original design for the shop included multiple compressed air outlets scattered about the shop. At the heart of this system would be a 60gal Ingersol-Rand 2-stage compressor providing at least 15 [email protected] Now months later, I've significantly revised and downgraded my plans. Part of it was financial, but most of it was a realization that all that I really needed was to be able to use my nail guns without the hassle of dragging out the compressor every time and tripping over hose.

Retractable Air Hose

To that end, I revised my plans and settled on a much simpler setup. I would put my existing 17gal Husky in the crawlspace below the shop, and run a hose through the floor next to my main assembly table. To this I would attach a combination regulator/filter/oiler and a retractable hose. This is precisely what I did.



The air filter/oiler unit is a $20 special from Harbor Freight...well, I got it for $20. It was down to $15 last time I checked…sigh. Unfortunately it only occurred to me after I had purchased the filter unit that I don't really want an oiler. While most of the time I'll be using a nail gun, I do occasionally wish to use the air hose to blow off the shavings from a piece in progress and I doubt that misting it with tool oil would be very good for the finish. I've mounted the unit anyway and plan to keep the oiler empty. Perhaps someday I'll move this device to another location on a separate hose and reserve it specifically for tool use. Or maybe not.

The hose reel was $30 for 20ft. It was the cheapest I've seen and while not as "industrial" as some of the more expensive units, I kinda preferred the compact size and appearance of this one. It also included a swivel mount. It works great right now…hopefully the mechanism will prove more reliable than the price would imply. We'll see.

Automatic Drain Valve

Another Harbor Freight special. The plan was to locate the compressor in the crawl space, accessed via a trap door in the floor. Draining it regularly via the drain cock would be somewhat of a hassle. What I needed was an automatic drain. Thankfully I found this site in about 5 minutes of research pointing to a product from Harbor Freight. It was fairly straightforward to install-except that the inner diameter of the hose running from the unloader valve to the pressure switch on my compressor was too small for the included fittings. I ultimately wound up buying a different fitting which suffered from the same issue-but was setup in a such a way that I was able to coax the hose over the inner brass piece by applying a bit of heat. A bit of sanding of the outer tube was also required to get the connector attached to the tee. It was a bit of a chore, but ultimately I managed to get it all to work. And just like the author of the site above, my new drain cock valve was no good…so I also replaced it with a part from HD. The thing about the drain is that it only opens when the compressor starts and shuts off. So I can either leave the compressor on so that it "tops off" periodically (thereby activating the drain) or program the switch it's on (see my other posts re: Insteon) to run it for a few minutes each day and give it a chance to drain any condensation.



Vertical Sheet-goods Pen

Finally, after filling the compressor, I used my new hose and old air nailers to build a 9' tall x 30" wide x 36" deep vertical sheet goods pen just outside the shop door and install some cheap pre-primed moulding around the pen face and shop doors.

This is the start of my next big project: the Garage Remodel.

Looks like it will work very well.

 

[sIKE]

Shop Air, and Sheet Goods Get A Home

My original design for the shop included multiple compressed air outlets scattered about the shop. At the heart of this system would be a 60gal Ingersol-Rand 2-stage compressor providing at least 15 [email protected] Now months later, I've significantly revised and downgraded my plans. Part of it was financial, but most of it was a realization that all that I really needed was to be able to use my nail guns without the hassle of dragging out the compressor every time and tripping over hose.

Retractable Air Hose

To that end, I revised my plans and settled on a much simpler setup. I would put my existing 17gal Husky in the crawlspace below the shop, and run a hose through the floor next to my main assembly table. To this I would attach a combination regulator/filter/oiler and a retractable hose. This is precisely what I did.



The air filter/oiler unit is a $20 special from Harbor Freight...well, I got it for $20. It was down to $15 last time I checked…sigh. Unfortunately it only occurred to me after I had purchased the filter unit that I don't really want an oiler. While most of the time I'll be using a nail gun, I do occasionally wish to use the air hose to blow off the shavings from a piece in progress and I doubt that misting it with tool oil would be very good for the finish. I've mounted the unit anyway and plan to keep the oiler empty. Perhaps someday I'll move this device to another location on a separate hose and reserve it specifically for tool use. Or maybe not.

The hose reel was $30 for 20ft. It was the cheapest I've seen and while not as "industrial" as some of the more expensive units, I kinda preferred the compact size and appearance of this one. It also included a swivel mount. It works great right now…hopefully the mechanism will prove more reliable than the price would imply. We'll see.

Automatic Drain Valve

Another Harbor Freight special. The plan was to locate the compressor in the crawl space, accessed via a trap door in the floor. Draining it regularly via the drain cock would be somewhat of a hassle. What I needed was an automatic drain. Thankfully I found this site in about 5 minutes of research pointing to a product from Harbor Freight. It was fairly straightforward to install-except that the inner diameter of the hose running from the unloader valve to the pressure switch on my compressor was too small for the included fittings. I ultimately wound up buying a different fitting which suffered from the same issue-but was setup in a such a way that I was able to coax the hose over the inner brass piece by applying a bit of heat. A bit of sanding of the outer tube was also required to get the connector attached to the tee. It was a bit of a chore, but ultimately I managed to get it all to work. And just like the author of the site above, my new drain cock valve was no good…so I also replaced it with a part from HD. The thing about the drain is that it only opens when the compressor starts and shuts off. So I can either leave the compressor on so that it "tops off" periodically (thereby activating the drain) or program the switch it's on (see my other posts re: Insteon) to run it for a few minutes each day and give it a chance to drain any condensation.



Vertical Sheet-goods Pen

Finally, after filling the compressor, I used my new hose and old air nailers to build a 9' tall x 30" wide x 36" deep vertical sheet goods pen just outside the shop door and install some cheap pre-primed moulding around the pen face and shop doors.

This is the start of my next big project: the Garage Remodel.

I am in the process of doing something close. I used Sch 40 PVC to run a couple of lines down from the loft of shop. I am very interested in the drain solution. Do you have any problems with the water just being pssst out? Mine AC is on a wooden floor and I do live in Texas and it is known to get a bit humid here. With the water being blown out twice every cycle I am wondering if I should even be concerned. As for which way you should go water is only added to your tank when the compressor is actually compressing the air for you. So I don't know if either approach is needed.

Thanks for the great idea!

 

[Grumpy]

Shop Air, and Sheet Goods Get A Home

My original design for the shop included multiple compressed air outlets scattered about the shop. At the heart of this system would be a 60gal Ingersol-Rand 2-stage compressor providing at least 15 [email protected] Now months later, I've significantly revised and downgraded my plans. Part of it was financial, but most of it was a realization that all that I really needed was to be able to use my nail guns without the hassle of dragging out the compressor every time and tripping over hose.

Retractable Air Hose

To that end, I revised my plans and settled on a much simpler setup. I would put my existing 17gal Husky in the crawlspace below the shop, and run a hose through the floor next to my main assembly table. To this I would attach a combination regulator/filter/oiler and a retractable hose. This is precisely what I did.



The air filter/oiler unit is a $20 special from Harbor Freight...well, I got it for $20. It was down to $15 last time I checked…sigh. Unfortunately it only occurred to me after I had purchased the filter unit that I don't really want an oiler. While most of the time I'll be using a nail gun, I do occasionally wish to use the air hose to blow off the shavings from a piece in progress and I doubt that misting it with tool oil would be very good for the finish. I've mounted the unit anyway and plan to keep the oiler empty. Perhaps someday I'll move this device to another location on a separate hose and reserve it specifically for tool use. Or maybe not.

The hose reel was $30 for 20ft. It was the cheapest I've seen and while not as "industrial" as some of the more expensive units, I kinda preferred the compact size and appearance of this one. It also included a swivel mount. It works great right now…hopefully the mechanism will prove more reliable than the price would imply. We'll see.

Automatic Drain Valve

Another Harbor Freight special. The plan was to locate the compressor in the crawl space, accessed via a trap door in the floor. Draining it regularly via the drain cock would be somewhat of a hassle. What I needed was an automatic drain. Thankfully I found this site in about 5 minutes of research pointing to a product from Harbor Freight. It was fairly straightforward to install-except that the inner diameter of the hose running from the unloader valve to the pressure switch on my compressor was too small for the included fittings. I ultimately wound up buying a different fitting which suffered from the same issue-but was setup in a such a way that I was able to coax the hose over the inner brass piece by applying a bit of heat. A bit of sanding of the outer tube was also required to get the connector attached to the tee. It was a bit of a chore, but ultimately I managed to get it all to work. And just like the author of the site above, my new drain cock valve was no good…so I also replaced it with a part from HD. The thing about the drain is that it only opens when the compressor starts and shuts off. So I can either leave the compressor on so that it "tops off" periodically (thereby activating the drain) or program the switch it's on (see my other posts re: Insteon) to run it for a few minutes each day and give it a chance to drain any condensation.



Vertical Sheet-goods Pen

Finally, after filling the compressor, I used my new hose and old air nailers to build a 9' tall x 30" wide x 36" deep vertical sheet goods pen just outside the shop door and install some cheap pre-primed moulding around the pen face and shop doors.

This is the start of my next big project: the Garage Remodel.

Pretty neat system Patrick.