LumberJocks Woodworking Forum banner
1 - 2 of 2 Posts

· Registered
Joined
·
2,185 Posts
Building a Work Bench

I did a trade for some woodwork with a guy who had a garage full of lumber and several nice hand tools. Most of the lumber was Oak.

I don't really like working with Oak. But I thought it would be perfect for a bench, and there was enough of it. I got lots of different lengths and widths. Most of it was 3/4". I forgot to take a "before" photo of the stack but here is a sample:



Now I intend to make a nice, sturdy bench, but its going to be more functional than artful masterpiece. Just something that I can really use with hand tools. Its my first bench, and there will be others later. So I really want this to be a quick project so I can get back to work on the stuff I really want to build.

Some may call this a "hack job." Call me a butcher, but I didn't even bother ripping the strips to the same width. As long as one side is flat, thats all that matters.

I started by rolling on the glue and clamping together sections of a half-dozen or so boards:



Then I glued up two of those sections:




At this point I have two sections that are less than 8" wide. This way they will fit on my 8" jointer to get one flat side.

Here is what the top will look like (It hasn't been jointed yet)



Here is the underside (notice the uneven widths)



The ends of the tool tray:



The sections laid out and ready for final assembly:




Don't worry, that endgrain will be covered with an end piece. For less than $20 bucks I got enough 4×6 and 2×6 Doug Fir for a very sturdy base. I also have a piece of solid mahogany re-claimed from an old desk for a bottom shelf, and a huge woodworking vice I got years ago at the flea market.

My friend the glue chisel…

On a side note, I thought I would take a moment to appreciate a very under-rated tool… My glue chisel. Its the old workhorse who doesn't whine or complain about the not so glamorous tasks like scraping semi-wet glue off a workpiece, gouging out a nail, prying double-stick-taped jigs apart, or popping bark off of a log.





Everyone should have a "glue chisel" ...someone's got to do the dirty work.
Way to go Blake. This will be fun to watch. Oak should not affect your allergies.

I have such a chisel. Also I have a favorite scratch awl that gets used for all kinds of poking and digging.

Steve
 

· Registered
Joined
·
2,185 Posts
Bench Almost Complete

More bench progress…

Here is the "tail" vice mortised into the end of the bench. You can also see how the underside of the bench looks with all the different widths I used:

P1010011

Clamping on the wider "apron" pieces front and back:

P1010006

And adding the end aprons with dowels:

P1010007

P1010008

P1010009

P1010010

As you can see I painted the 4×6 fir base black:

P1010030

I leveled the table with shims under the feet and then bolted the legs to the floor:



And then the fun part began…

P1010012

P1010014

I routed the edges of my vice jaws on the router table:

P1010018

P1010020

The vices came out really nicely. I made the tail vice so it would span across the entire width of the bench. That way I could have bench dogs along both edges of the bench for wide clamping.

P1010021

P1010023

Nearly complete… now all I have to do is add the dog holes, and a little sanding/finishing. I actually made it to the Sacramento Woodworking Show on Sunday and picked up some brass Veritas bench dogs.

P1010027

I think it looks really good with the black base.

P1010025

(See all the shavings on the floor!)

UPDATE:

Here are the links to the finished bench and cabinet in my projects:

Very nice Blake. I'm jealous.

It will be interesting to see if your endcaps cause any problems with wood movement. Usually these are applied with a sliding attachment and only glued at the end. But you seem to have a well placed horseshoe, so it will probably be just fine.

The thumbnail edging on the vice chocks are sweet.

Good job,
Steve
 
1 - 2 of 2 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top