LumberJocks Woodworking Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 500 Results
  1. Workshop Difficulty removing table saw blade

    I am fairly new to woodworking but I have most of the tools. My Forest WWII blade has been on my Jet cabinet saw forever. Recently I switched it out for a flat ground Amana blade. All went well until I tried to remove the blade. It would not budge. I pried it with a screwdriver, wiggled it...
  2. Power Tools, Hardware and Accessories
    Are they worth using? They seem like a lot of trouble but if they work well then it may be worth it. If you use one or used to have one what are your opinions, good or bad? Thanks Myles
  3. Power Tools, Hardware and Accessories
    I purchased an older Laguna Fusion tablesaw last year. It came with some inserts but I ordered a couple of new ones to create some fresh zero clearance. The problem is that the blade won't drop enough for the new blank insert to sit flush. I see in the cabinet the stop but I can't tell if...
  4. Power Tools, Hardware and Accessories
    Hey everyone, and thank you for reading this, I'm new to woodworking with practically no experience, I'm looking for a table saw to start my own shop, but things are kind of complicated choosing one, I live in México which makes it a little more difficult, tables saws like DWE7491 are not...
  5. Projects Dining Table

    This was a fun yet quite challenging build. I got to play around with some new joinery techniques, which was great, but getting the legs to line up just right with the table top definitely took some patience. I have to say though, the challenge was worth it, and now it’s something I get to...
  6. Tablesaws
    Bought second hand, tuned it up in my shop but have one issue. If i lock the fence down for a cut and want to make a fine adjustment, ie:1mm or similar the only way to do is unlock and gently “bump” fence then lock then check. Seems like a bit of guesswork, my old saw you could lock the fence...
  7. Tablesaws
    I'm upgrading from a jobsite saw. I want to spend right around $2000 and I don't want to get the SawStop contractors saw. What do you think would be the best options? TIA!
  8. Projects Large cherry mirror in golden ratio proportions

    Mitered corners strenghtened with splines. Decorative flutes, birch plywood back. Osmo oilwax finish
  9. Marketplace Classifieds
    Saw was made in Tennessee and is in excellent condition. The worst of it is a few chips and one rounded corner on the original green topped 50” rip table. Includes a sharp 8” dado stack, a 10" carbide blade, a new Woodpecker's Rip flip (micro adjust for rip fence) and original inserts & guards...
    $2,500 USD
  10. Power Tools, Hardware and Accessories
    Hi, I picked up a used Craftsman table saw (351.218330) and it didn't come with the riving knife. Is there anyone out there with the same saw that could take a photocopy of their riving knife? This way I could get one made, I'd be happy to send a few $'s for the photocopy. Unfortunately...
  11. Projects Found a spot in my shop not being used.

    I have a 5/8" oil field sucker rod in the middle so it will spin around easy! |This was the last place in my shop I don't have junk and things cluttering up and this is great for it is out of the way hanging over the sink. They do get dusty but a little air every once in a while makes it back...
  12. Projects Thermo ash plate

    Привіт, друзі. Давно не займався проектами. У нас в країні війна. Російська Федерація віроломно напала на мою країну. Усі, як один, стали на її захист. Як колишній військовий я теж повернувся до лав Збройних Сил України. Незважаючи на це, при першій нагоді намагаюся повернутися до свого ремесла...
  13. Projects Custom Milled “ Old Growth” flooring

    final product from an old cabin/granary brought back to life !
  14. Power Tools, Hardware and Accessories
    Hi All, I'm new here but looking for some advice. I have the opportunity to get a 94' powermatic 72a with a 5hp single phase motor in great condition for FREE. I currently have a 99' Delta Unisaw right tilt with a 3hp motor. I would be selling the Uni and using the cash to get new blades and...
  15. Projects Shop Built Table Saw Mobile Base

    My neighbor brought over an 8’ 1x4 piece of fir the contractors left after working on his house and asked if I could find a use for it. Of course being a woodworker I knew I could and decided to make something I needed/could share for others who may need to move stuff around in their small...
  16. Journal Replacement Chest of Drawers

    Frames are done...time to raise the panels that go into them. Had 4 already cut to ROUGH size...needed 4 more for the other frame. labeled as to where each goes...I hope. Crosscuts to rough length, rip cuts to rough width. Plane an edge or two to straighten things out a bit....done..for...
  17. End Grain Top, A true labor of love

    I have had the opportunity to build several, end grain, butcher block cutting boards when a close friend asked if i could make a counter top for a kitchen island. The process is the same, but it is considerably more work to build a larger top…especially in a small shop like mine. I was...
  18. router table & extension wing for tablesaw

    Router table wing and extension wing for my Ridgid R4511 TS. The wings are made from 2 layers of 3/4" MDF trimmed with some salvaged mahogany trim. I added a router plate, t-track, miter track and safety switch from Rockler. The Formica was given to me by a friend that works in a cabinet shop...
1-20 of 500 Results
Top