Search Results for ‘outdoor table’

No fasteners just gorilla wood glue. Timberpro internal wood stabilizer, Thompsons water sealer letting it Grey up naturally.

I had an attorney friend that wanted a specific sized table for her deck. This is what I came up with. All of the lumber was from old posts/boards that I salvaged and cleaned up. They cleaned up pretty well. Got a nice little commission off this piece. She chose to leave the table natural to...

I wanted to make use of a bunch of 6×6 cut-offs I had from a deck project, so I ended up with this on my deck. It's 9' long and 42" wide. Probably weighs 350lbs. It's held together with 6" sts screws and 3" deck screws. I'll do a couple of 42" long benches for one side of it eventually. Haven't...

Here's a few pics of my finished cedar patio table. It took some time to build, but it's totally worth it. Total cost was ~$140, which was way cheaper than buying anything similar in a store. The closest I could find pre-made cost $499. The table top is made from 5/4 cedar decking and the...

Picnic tables traditionally are too low for arthritic old folks (me) and frequently run uncomfortably close for overweight arthritic old folks (still me). So, I made some modifications to this building supply store picnic table kit. I realize a kit picnic table is kind of outre on a wood...

Douglas Fir all the way around. Stained with Early American from Miniwax finished with oil based spar urethane. 2×12's are table top, 4×4 legs, 2×4 frame. Bench tops made from 2×6's.

I made this picnic table and benches after I saw a very similar design someone else had posted on LJ. Table and benches are cedar and around 10' long, so it can seat quite a few people. I finished it with an epoxy sealer followed by a marine varnish (based on finish from the Wood Whisperer)...

Last summer I was asked to make a cedar table and a couple of benches based off a table design likely from Pinterest. Not a whole lot to say about the project, except that it's all made with floating tenons and it was a cinch with the jig I made for my router. Took some time to make the jig, but...

Really happy with this one, even if it's only because now I can actually use the awesome grill that it houses! Entire table is made from 4/4 cypress from a local sawmill milled down to 3/4" thick. The legs are one piece that goes top to bottom, then below the lower shelf are 2 pieces glued up...

A big farmhouse table I made for my parents. Douglas Fir all the way around. 4 2×12's compose the table top, 4×4's for legs and 2×4's make up the frame. Finished with water based spar urethane.

This is an outdoor end table I made last month. I built a small deck, 10' x 8' or something like that, it fit a corner of my sloped back yard. I have a few chairs and a chiminea I made on the deck and I thought I should have an end table on the deck as well. I looked online to find styles and...

Outdoor wine bar/table made from eastern red cedar. Finished with teak oil

My youngest daughter is in college in KC and she and 4 of her friends moved into an apartment off campus in January. They have a small balcony they like to sit on and have coffee and she thought it would be nice to have a little custom table to put out there. Hence the table project shown here...

This is a 12 foot by 48 inch Redwood table for a family of 7. The table has 6 legs and three breadboard ends, all done with pinned mortise and tenon joinery. Since the table is for outdoors, the top boards have gaps to allow for drainage. I used roofing nails for spacers. The table was so large...

I decided to build this slatted cube end table to challenge myself using only dowel joints. 136 dowels to be exact! This was actually my first time using dowel joinery, and I ended up using and comparing 2 different doweling jigs in the process. Both had pluses and minuses in my opinion. The...

I recently made this for a friend of mine completely out of cedar. He needed a table to sit outside next to his smoker to use as a landing spot for tools, trays and all the gloriousness that comes out of that smoker. It's based on some plans from Woodsmith called the Tile Top Table. My buddy...

A co-worker of my sister in law wanted me to build her a table, 2 benches, 2 adirondack chairs, and footstools. She had seen some pictures of adirondack chairs i had built from my sister in law. She had a picture of a table she saw for sale in Atlanta that she really liked. She wanted me to try...

Here is an outdoor table I finished a while ago. Made out of construction grade plywood, nailed and glued with liquid nails. Once the tyvek was on I wrapped it with metal lath (missed the pictures) then coated with cement. The last picture shows how I tried to get the plywood straight. It's been...

I recently moved into a new place which lucky for me had a large entertaining deck at the back of the house. Ambitiously i decided that i didn't like the idea of purchasing a cheap glass table and chairs and that i would build a large table to fill the space nicely and provide a great place to...

Hi I just joined to the lumberjocks community because I like woodworking projects. I want to share my first project that is an outdoor table for a big green egg. I used as an example a project that is posted also here. I used pine wood and all the joints were made with kj tools and screws. I...