LumberJocks Woodworking Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 60 Results
  1. Headboard

    I made this headboard out of pine and birch ply. I added LED strip lighting to the underside of the top for reading in bed purposes. From start to finish it took me eight weekends. The face-frame is joined together with biscuits, and then glued onto the plywood backing. This is then pocket-hole...
  2. Custom Library Build

    Finished a room renovation to convert my living room into a library. I added in a coffered ceiling and a gas fireplace too. There is a link below to a video if your interested in the finished project or want to see the details of how i built the room. If you have any comments or suggestions...
  3. Built in bookcases

    These are built-in bookcases that I designed and made for my wife's sitting room. They are made from birch plywood and poplar. I'll be finishing up the shelves soon. They'd are also birch ply and polar. They have reinforcing edged on the front and back as I wanted them not to sag on the 34+"...
  4. Fixing up my room a bit

    1:Built in closet shelves 2: crown moulding,I think it looks nicer that I installed it upside down 3: My room before painting 4: after painting 5: almost done 6: putting in crown moulding,I finally had another excuse to buy an air compressor! :)
  5. Blanket Chest

    Custom made blanket chest from spalted red oak. Finished with a dye stain.
  6. Miter Sled

    I just built this sled for moulding in some raised panel doors we are doing. I added an insert to bevel the miter. It is removable using threaded inserts in the sled. It is a piece beveled at 7 degrees. This allows the moulding to set flat on the bevel of the raised panel. You can remove the...
  7. Window Trim

    I redid the horrible window trim in my bedroom and bathroom while insulating (w/ spray expanding foam) some large gaps around the windows (the gaps can be seen in the last picture). I used pine moulding and cheap pine ply from the local Home Depot, so nothing fancy material-wise. The large...
  8. Powder room redo

    Our circa mid 60's powder room had never had a redo, still sporting 1" pink floor tiles, a flimsy build-in vanity. The wife went to visit her mother for a week and I set out to surprise her! Ripped it all out, new underlayment and tile, wainscoting, built a new "table" on which to set the new...
  9. Couple of wooden planes

    Here's the story: my main project is a workbench build. Almost done. You know, "almost" may last longer than you want it to. So to finish it I need a router plane (have couple of ideas, but they're still cooking…). And to make a router plane I needed couple of other planes: round moulding...
  10. Cake decorated frame - hang it or eat it?

    I made this frame with my moulding planes, then decorated it with a pastry bag and spackling. With a little stain it looks like a chocolate cake, hmm, I am getting hungry.
  11. Cherry Dresser

    I built this to match a low double wide version that I built for her a few years ago (the last picture is the low dresser that I built first). Highlights of this project included the bun feet and the stacked molding. The stack of molding includes one part that was made on the router table, then...
  12. Bathroom Vanity & Mirror

    This was an unexpected project I made for my mother, she was planning on renovating the bathroom in the next couple of years but we noticed a leak in the wax seal of the toilet, after I played plumber for a while and noticed that some of the floor needed to be replaced due to water damage, yada...
  13. Hannah's Bookshelf

    This project was a request from my wife. She wanted a bookcase to fit all of our 2 year old daughter's books on. She wanted it to sit under the window ledge in her bedroom. Lesson's Learned: ~I tried to cheat and not sand the project as fine as I should at first. I stopped at 120 grit I...
  14. Simple Key Holder Shelves (October 2012)

    Outgrew the old one…or should I say over cluttered the old one. Just simple shelves out of a scrap 40" piece of 1×12. Wanted to throw something together to test out the new router table and try out Target's EM6000 I just got. The table is a tank and the finish is sweet! As with any small project...
  15. Cherry Wainscoting

    Here is the cherry wainscoting I designed and installed in my office downtown. The panels are stub tenon and groove construction, with a few well placed pocket hole screws to simplify assembly. Two corbels are let onto the stiles with 1/4" deep grooves. There are two 6' panels, one 32" panel...
  16. Vaulted crown moulding

    Just finished a whole house of crown moulding including these awesome looking vaults. I like this alot because the vaults are not too steep. Steep vaults with crown looks wierd to me although it is preference. This is six inch georgian crown.
  17. My wife's kitchen

    I designed and built this small but functional oak kitchen for a new home my wife and I built in the summer of 2010. I like to think outside the box when designing projects. This has many hidden treasures. My favorite is the soft close doors and drawers. We like the accessibility and...
  18. Cherry Barstools

    I bought the air dried 8/4 cherry that I used for these stools in Vermont two summers ago, not sure of what it would actually become. Even in rough form it was nice looking but once I started planing it down the real beauty began to reveal itself. It has dark lines (both green and black)...
  19. Eye Glasses Holder

    A fun and quick scroll saw project. The design is by Steve Good. I made several of these. The ones pictures are in bloodwood and walnut.
  20. Hannah's Dresser

    When I found out that my wife was pregnant I immediately decided that I wanted to build a dresser for my new child. I wanted it to be something that they would/could use for generations. My wife wanted something that we could use as a changing table, so that dictated the height. By the time I...
1-20 of 60 Results
Top