LumberJocks Woodworking Forum banner
  • Please post in our Community Feedback thread for help with the new forum software! If you are having trouble logging in, please Contact Us for assistance.

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-15 of 15 Results
  1. Built-in bath vanity, storage cabinet and matching tub surround

    Custom built-in bath vanity, above counter storage cabinet and matching tub surround. All doors and the matching tub surround are made of solid wood with tongue & groove beaded planks. Doors are held together with battens on the inside which have been dovetailed into the planks. No glue on the...
  2. End Table made from reclaimed cedar for a beach house

    This end table was made to match a coffee table for a beach house. As such, the build was similar. It was made from reclaimed cedar 2×6s and 4×4s that had been previously used on a large deck for railings and door frames. I jointed and planed off the old paint, resawed some of the boards for 5/8...
  3. Live Edge Bartop - Sofa Bar

    This was a custom project for a home theater. The owner wanted a custom bartop that would sit behind a large couch which was directly in front of their home theater screen. We settled on a design that would allow bar stools to sit under the bartop at a normal bartop height of 43". The bartop is...
  4. Coffee table for a beach House

    This coffee table was made from reclaimed cedar 2×6s and 4×4s that had been previously used on a large deck for railings and door frames. I jointed and planed off the old paint, resawed some of the boards for 5/8 thick slats for the bottom deck. The apron and stretchers are attached using loose...
  5. Mitered Jewelry Boxes

    I had a customer who wanted a custom jewelry box with mitered drawers. I made three at the same time. The boxes are made from walnut, cherry and white oak . Each was a little different. The walnut box was finished with Genral Finishes Arm-R-Seal satin. The cherry boxes were finished with Watco...
  6. Bar top overhang

    This is just a slab counter top. The walnut slab has a very large crotch which makes it visually appealing. The slab was sanded to 180g and finished with an oil based urethane (GF Arm-R-Seal satin). The slab was purchased from Second Chance Hardwoods in Elkton, MD.
  7. CNC Tool Bit Holder

    Needed a bit holder for the CNC. Used two pieces of 1/2" baltic birch ply glued together. Has holes for both 1/4 and 1/2 inch bits as well as the bits plastic containers. Added small bins for other misc parts and wrenches. Sprayed with GF High Performance Satin.
  8. Special box

    I made a custom box for an eight year old boy to hold his watches, cards, arrow heads and whatever else he wanted decided to place into it. The box is made out of cherry. The top has an eagle that has been carved into a piece of maple (cnc). The top of the box was a special piece of cherry that...
  9. Built-in Bath Vanity, Counter-top and Utility Cabinet

    This is a custom piece for a bath remodel. It includes a base cabinet with a walnut counter-top, drawers, doors and a utility cabinet. The cabinets are made from pre-finished maple ply. The face frames and doors are made from 7/8" poplar. It is finished with a semi-gloss hybrid paint from SW...
  10. Cedar Light Post

    Here is a light post made from cedar. It is a square post made with 7/8 cedar planks, rabbited and glued. Base and moldings were then added. The base is made to fit over a 4×4 pressure treated post with room left over to accommodate a NM cable for power to the light fixture (light fixture not in...
  11. Walnut Dining Table with Breadboard Ends

    Here is a walnut dining table made from a tree that was downed during a storm at my customer's property. Wood was air dried for about two years and stored in a climate controlled environment for another year. Top is about 1 5/8" thick. The finish is General Finishes Arm-R-Seal Satin.
  12. Walnut Dining Bench

    Here is a walnut bench to go along with the dining table made from a tree that was downed during a storm at my customer's property. Wood was air dried for about two years and stored in a climate controlled environment for another year. Top is about 5/4" thick. The breadboard ends are pinned...
  13. Large Walnut Dining Table No2

    Here is another walnut dining table made from a tree that was downed during a storm at my customer's property. Wood was air dried for about two years and stored in a climate controlled environment for another year. Top is about 1 1/4" thick and the dimensions are 102"L x 72"W. The finish is a...
  14. CNC Cart

    I needed a cart to house the computer, monitor, bits and tools for the CNC. Came up with this. Included a file cabinet drawer as well.
  15. Live Edge Walnut Bar Top

    I recently installed a live edge bar top that was made from two slabs of black walnut (8/4" x 18" x 12'). The slabs were broken down into smaller pieces to form the U-shape of the bar. The slabs are joined by loose tenons to maintain a flush top and mechanical fasteners to draw the joints...
1-15 of 15 Results
Top