LumberJocks Woodworking Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 35 Results
  1. New table saw storage - Chest of drawers & extension table

    I just uploaded photos of my new woodshop under that heading, if you are interested. I added a new 3hp table saw with a 50" fence last week and needed to recoup come of the storage I lost when I sold my old table saw & cabinet. I put together a chest of drawers under the right side table...
  2. Shop-made Table Saw Miter Gauge Slot Extension Table (plan linky included)

    Another COVID-19 Lockdown Shop Project - Mitre gauge slot extension table Scrap wood Fence clamps: https://www.leevalley.com/en-ca/shop/tools/jigs-guides-and-fixtures/72984-mounting-clamps-for-fences-and-jigs Project Completion: Half a day in May 2020 Project Delay: 8 years+!!! Source of Plan...
  3. Folding Extension Table for Sailrite Leatherwork Sewing Machine

    I made a quick and easy folding extension table for my Sailrite Leatherwork sewing machine. It's quite useful for this application, and the folding shelf brackets might prove helpful for other shop projects as well. Here's the video… Made from 1" thick MDF, stainless steel folding shelf...
  4. Mesquite Extension Dining Table

    Mesquite Extension Dining Table-Here is the table I will post more detail pictures when my photographer gets done with them.The base is six bentwood legs tied together in the middle with a round piece inside.The top is 56" diameter and expands to accept a 20" leaf.All is inlayed with...
  5. Pedestal Extension Table

    Well after reading so many posts here and learning so many things, I have finally decided to join and become part of this wonderful community! I would also like to share the last of a video series I did on You Tube showing a table I built for my kitchen. It was by far the most fun I have had...
  6. Cherry and Maple Side Table, by hand

    Side table made with hand tools. No measurements used, all ratio and proportion based with hip height being the module. Curly maple drawer face from my yard in coastal Oregon. Lots of fun.
  7. Mesquite table

    Mesquite table-Now That I have gotten good pictures I want to show everyone.This table is Mesquite with a Walnut/Maple bentwood curved line sandwiched in between two halves of the table.The joinery close up is under the table were the legs come together. The pedistal base is all carved and hand...
  8. Flip-Up (Fold-Down) Table Saw Out-Feed Table

    I picked up a new table saw the other day (Ridgid R4512) and knew the first thing I wanted to add was this out-feed table. I am restricted on space (two car garage but my wife's only request is that she's able to park in it at night) and therefore make all of my stands/benches mobile and...
  9. Pomele Bubinga extension table

    A little while ago I finally got around to building myself a dining table. I knew that I wanted it to be an extension table and I planned on making it with some spectacular veneer. Other than that I was a little stumped. I thought it would be fun to do something new to me and in the end I...
  10. Street cone dust cyclone build

    This is a street cone I built from a street cone Check out the vid of the build Http://youtu.be/dcbAB_gbPic Please leave a comment if you find this of any use Thanks for watching
  11. Table Saw Extension Table Cabinet

    This is an extension table cabinet that I built a few months ago for my table saw. It was primarily intended to provide additional storage for my table saw accessories. It's constructed from Birch plywood. I put it on casters to make it easy to move in and out from underneath the extension...
  12. 8/4 Walnut Extension Table w/ Adj. Hairpin Legs

    I haven't posted here in a while with the new home/shop. Looking forward to it again. Here's an 8/4 Walnut Table with 2 extension 12" each (not pictrured) to make it 78" or 54" without. Rockler wood extension systemhttp://www.rockler.com/extension-slides-20-length, No pins were added and...
  13. Walnut Dartboard Cabinet

    Dartboard cabinet I built for a young lady to give to her husband as a wedding gift. Built from black walnut with book-matched door panels.
  14. Jet 2.0

    This is a project I call Jet 2.0. I bought this tablesaw from a local cabinet company here in Wichita Kansas that had upgraded to Sawstop machines. I pondered over that very same idea for the last two or three months until stumbling on this machine on craigslist. Paid 1100 for it although it may...
  15. TABLE SAW OUTFEED TABLE COMPLETED

    OUTFEED TABLE NOW COMPLETED, STABLE, SMOOTH OPERATION & WORKS GREAT SEE 3 ADDED PHOTOS & ONE CLOSEUP DETAIL OF THE TELESCOPING LEG SUPPORT. Hi, All . . .The table core is two 3/4" MDF Sheets bonded together with the top & bottom laminated. I thought at first that laminating the bottom was...
  16. Coffee Clock for a cafe

    Another clock for christmas
  17. Table Saw Outfeed Table

    This is the outfeed table I built for my table saw. I had seen a similar design online and figured that it would work well for me. The frame is 1×3 poplar face screwed(no fancy pocket hole joints here. The top is 3/4" particle board covered with a light blue speckled laminate that I had left...
  18. Power Tools, Hardware and Accessories
    I am anxious to get this figured out since the only way this is going to fit into my garage is to get enough mobile velocity so that it can make it's own space! I just bought an old Powermatic table saw and need a mobile base for it. It is a pretty old one with an open bottom on the cabinet...
  19. Power Tools, Hardware and Accessories
    I have installed a melamine router table insert into the space on the right side of the table saw. This is temporary arrangement because I want a MDF top with laminate for a permanent top. What I was thinking about was removing the stamped steel plate on the right side of the table and replace...
  20. Designing Woodworking Projects
    Hello! I'm working on the plan for a dining table but having some back and forth with myself and my wife about the design. I need help! Thanks for reading and did your thoughts. Known plan so far: Hairpin legs No apron 8' long closed, 42" wide, 7/8" thick. Breadboard ends Must be...
1-20 of 35 Results
Top