LumberJocks Woodworking Forum banner
  • Please post in our Community Feedback thread for help with the new forum software! If you are having trouble logging in, please Contact Us for assistance.

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 500 Results
  1. Projects 4 Drawer Chest of Drawers

    4 drawer Chest of drawers, built to replace an old worn out one. Frame & Raised Panel sides, drawer fronts are raised panel look. Top has a bread board edge, and is Spalted Maple.. Front view... Drawer details, frame & raised panel sides Bread board edges.. Knob details
  2. Journal Replacement Chest of Drawers

    Time to start on building 4 drawers....need 4 blanks for the drawer fronts... I need one edge to be jointed... once I have all 4 blanks jointed.. And THAT edge marked with a J to keep track of them...I can place that edge against the mitre gauge on the tablesaw...square one end...measure for...
  3. Workshop Cabinets

    These are the cabinets I built for my garage converted to a workshop. There is a bath on the other side of this wall that I was able to plumb a sink into. Cases are pre-finished birch plywood. Doors and drawers fronts are 3/4" Melamine. Cases were pocket screwed together. I used leg levers for...
  4. Cabinet for Dining Room

    I finished this cabinet earlier this year, Can anyone guess what the timbers are ? Yes the door and drawer panels are solid with natural feature , see 4th picture I plan a wine rack in lower right but at this time do not have suitable timber Garry
  5. Storage Bed II | Custom

    This is a bed that was completed in January 2011. It is a knock off of my Original Storage Bed. I basically took the bookcase top section off and raised the storage area under the headboard. I call it the Storage Bed II. It has a lot of storage. I only have drawers on one side. Those...
  6. Two Drawer Band Saw Box from Pallet Pine

    June, 2011-I came across some pallet lumber with rather thin sections of pine. After salvaging the wood I planed them with my motorized hand-held planer. Then glue and clamp made a nice block for a band saw box. My own process recently for doing these glue-ups is to put the nicest or most...
  7. Custom Pantry Cabinets

    Sorry, all you have to do is tilt your heas to the left. Anyways when the cabinets were connected they were 7 feet long 6 feet tall, and 17 inches deep. The shelfs were 11 inches deep, allowing for 5 inch door shelfs. This enabled her to see what was on all the shelfs. The door shelfs were her...
  8. Porter Cable Dovetail Jig Station

    I just bought this dovetail jig from Porter Cable as I have always loved this joint and I cant quite master the hand cut joint yet, in the mean time I thought this jig would help me with various different joints, although this is the basic jig that came with 1 template that can cut half blind...
  9. Abomination Dresser

    UGLY! unfortunately made of second hand particle board for the sides (explaining the paint/paper mache); made of oak and whitewood board for the drawers. everything was pretty much second hand now that i think about it. if you appreciate woodworking you may find this quite distasteful.. ABOMINABLE!
  10. A Nice Down Sized Workbench

    I helped a friend of mine build this work bench for his 10×20 workshop. The bench is 18in wide and 72in long. Space was a necessity so only usable 18in top was good. Made of vertical grain Douglas Fir with a store bought top called rubber wood I know is best as Ramen. The vise was...
  11. Wall Coat Rack with Handy Drawers

    Wall Coat Rack with Handy Drawers Reclaim Wood and Pallets can always make nice projects. Even the defects can be interesting if you like this style. I have done quite a few projects out of reclaimed or pallet wood and I will post them for those who do like this approach in woodworking. This...
  12. Custom 4-string bass guitar

    This bass started from all rough cut lumber from my local yard. Planed it all down, cut it to size, glued it up and cut out. I then shaped, sanded and finished all by hand. The top of the body is curly purpleheart and the main body is ash. The neck and fingerboard are both made of curly maple...
  13. Re-claimed wasted space

    After assembling my new Delta belt/disc sander I saw an opportunity to use some wasted space. Looked like a good place to put in a couple of drawers for smaller items or storage. There is plywood on the bottom brace with drawers above and below it. Not much of a project but it helps make the...
  14. Ridgid OSS Rolling Stand

    Here is my rolling stand for a Ridgid oscillating spindle sander. The cart has 3 full-extension drawers on heavy duty ball bearing slides. The wheels are Steelex double locking swivel casters in the front, and fixed casters in the rear. It is nice to have a dedicated space for all my sanding...
  15. Storage Unit For A Mitsubishi Delica SUV

    A friend of mine asked me a few weeks ago if I would be interested in taking on a project for his vehicle. He wanted some storage cupboards and drawers in the rear of his SUV and also wanted a fold-up bed. I told him that in order for me to build this for him, that I would need the vehicle...
  16. A master bath with no drawers

    Here goes my first LJ project post. I have dual vanities in our master bathroom that were lacking drawers. I watched my wife silently struggle with all the plastic gadgets under her cabinet in an ill attempt to organize the mess for several months, okay two years, and I recently set out to solve...
  17. Utility Storage Cabinets

    No fine woodworking to be found here, just a built in utility storage cabinet. Plywood carcass, face frame, drawer boxes and separate draw fronts. Straight forward and actually, I farmed out the doors, drawer fronts, and three of the drawer boxes. It's hard to photograph this big piece in a...
  18. FIRST HALF-BLIND DOVETAILS

    I had some drawers to make, and they ended up being a few firsts for me: -First half-blind dovetails (hand-cut) -First traditionally constructed drawers (half-blind dovetails in front, full dovetails in back, drawer bottom in grooves in front and sides, sliding in under the back (see picture)...
  19. Pine Dresser

    This happens to be the first woodworking project I ever worked on. Period. I had never even made a bird house before. I don't know what came over me but all of a sudden I just had to start making something with wood. I watched Norm Abram build this dresser in a 30 min show so I thought "surely...
  20. Base ball loft | Custom

    This was a project that we finished and delivered on Christmas eve. It is a baseball loft. It is based off my baseball bed that I normally build with the customizable headboard. This is real similar to the baseball loft I built last August. Here are some of the changes I made to this one. I...
1-20 of 500 Results
Top