LumberJocks Woodworking Forum banner
  • Please post in our Community Feedback thread for help with the new forum software! If you are having trouble logging in, please Contact Us for assistance.

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 448 Results
  1. Deluxe Boat Bed | Pirate theme| Custom

    This is a boat bed that I just finished up. It was completed in January 2017. I finished it out in our standard Navy finish with a red pinstripe. All the wood is Pine wood with a Red Mahogany finish Minwax. We did a lot of extra feature on this one. One being the Gallery Rail on the headboard...
  2. Planer Cabinet

    I recently bought a Dewalt 735 planer and needed a rolling cabinet for it. At 90 lbs, the planer was just too hard and dangerous to move around. Nothing fancy. Case is made from 3/4" Baltic birch plywood. Back is also 3/4" just because it avoided buying more plywood. Case is just a bit...
  3. Flat Screen TV Stand

    This is my first large furniture build with any degree of complexity. As always comments and critiques are welcome. I used a plan purchased from U-Bild. I built this during my first week of furlough this year and finished it during this past week. The top, shelves and sides are 3/4" maple-faced...
  4. Keurig Coffee Holder

    This is a Keurig coffee holder I made to store the coffee and tea the family likes to drink. I decided to make it out of left over hickory from another project. I made it with three shelves, one for each family member. Basic simple design with a lacquer finish. This is the second type box for...
  5. Six Drawer Dresser - Bedroom Set Piece 4

    Well, its finally done! The last piece of my bedroom set. This is a six drawer dresser. Its about 65" wide, and 34" tall, with a depth of about 18". The case construction is birch plywood for the top and bottom, maple ply for the sides and center support, and then more birch plywood for the...
  6. Maple Mortise Madness

    120 mortise and tennons, 12 dovetails, a lot of biscuits, a few dowels and there you have it! Two end tables and a couch table made of maple finished with three coats of 35 sheen lacquer. The only mechanical fasteners used are for the undermount soft close slides for the drawer. One end table...
  7. A rolling base (w/ drawer) for my Craftsman 13" planer

    My planer weighs roughly a metric ton, and is a real pain to move and use on the floor. I built a ~10" tall rolling base for it so I could position it where I need it, and the whole thing tucks perfectly under one end of one of my work tables. I got a little bit fancy with the coloring, but I'm...
  8. Dovetailed Cherry Cabinet

    This small wall cabinet was built of cherry and features a turned walnut knob, frame-and-panel door pinned with walnut dowels, and a dovetailed drawer and case. For a finish, two sealer coats of clear shellac were applied, then lightly sanded. Next, four coats of Minwax antique oil were applied...
  9. Euro-slide installation jig (Screws-N-Plywood)

    There are a lot of different jigs on the market for mounting drawer slides. The are all based on holding the slide in place where it needs to go and screw it in place. This gives a lot of room for error, because the screw holes are so big and you do not have a lot of room inside the cabinet to...
  10. Man Box For Husband

    Well its finally done! I finished the "man box" I was making for my hubby. It only took us a month working about 3 hours almost every night somewhere between 80 and 90 working hours total however a lot of that was learning time for me I take longer then I should to get things done since dad...
  11. Router Table Cabinet Insert

    My router table cabinet insert is finally finished…ish. Just a few details to mop up. Not that the blue color gives it away but it's a Kreg table that I upgraded with a Jessem Mast-R-Lift II and a PC 75182 motor. The cabinet is loosely based on Kreg's plan but since I wanted to incorporate a...
  12. Curved to Perfection

    This is a 3 drawer gentleman's chest of Peruvian walnut and cherry. The case is constructed with handcut dovetails. The drawers are coopered and feature drawer slips with sliding housed dovetails and through dovetails. Finish is BLO and a handrubbed Daly's Pro Fin. www.wrightwoodworks.com
  13. Barn board kitchen cabinets

    Made some kitchen cabinets out of floor boards from a haymow. Most boards are elm, with some birch, red oak, white oak and maple. The boards were in the haymow as floor boards for around 80 years. The carcasses are made with 3/4" birch plywood. The drawers are maple with finger, dadoes, and...
  14. Small grease pot

    This was a fun simple project based on a few i've seen here by Mafe. It would look 100 times better if it were walnut, but i can't seem to find any. In fact all my projects would look better in walnut. It's not perfect, but i'm still getting better and i like it, so enjoy. It is made of pine, i...
  15. drawer box

    This is my Attempt 23. I love box with mechanisms, more than a box, they are a toy for me. I remember the hours playing with my grandma´s box before her eyes fearful. woods are laurel, cancharana, mora y lapacho. If some one is interested in the english name, I can search in my archive. In...
  16. Kitchen Drawer

    Our house was built in 1972. The kitchen cabinets are original to the house and were these tacky looking English Tudor sort of things in a style popular back then. They were covered in this sort of "industrial grade" contact paper that was bubbling and peeling. The kitchen drawers are these...
  17. A kit box for the hand made drill

    In my previous project post [link] I made a hand drill ala Izzy Swan to use at work when I need to drill a hole in new tuning pegs. This time I made a little kit box to hold the drill and some extra drills plus a few screwdriver bits. I don't expect to need this very often, so keeping it in a...
  18. Kitchen Cabinet

    I completed this storage cabinet in March of 2017. My wife requested this cabinet to store all of her cookie cutters and decorating tools. The case and drawers were built with baltic birch plywood. The drawer fronts and the base were constructed with poplar. The top was made from red oak...
  19. combination lock drawer box with spring mechanism

    well, in the drawer box mechanism I wanted to work with sliding dovetail in order to make less evident the mechanism. First of all I work with equal lumber than side. Then I made a box (sailing box, coming soon in Lj :-) ) where my ploy were put four sliding dovetails (one worked, the other were...
  20. Dresser & Night Stand

    I have been wanting a new dresser and night stands in for our bedroom for a while now, all of our bedroom furniture is dark and the old dresser was natural maple so it kind of stuck out a bit. I managed to make all of this out of material I had around the shop from previous jobs. It is made of...
1-20 of 448 Results
Top