Search Results for ‘bucket’

Got a new Porter Cable Table Saw and I have been making ALOT of sawdust. They way the it is built it forces all of the saw dust out of a dust port out of the back of the saw. Sawdust was getting over everything. Needed a cheap solution to capture the dust. I don't have enough money for a full on...

Hello All, I made this dust collector in order to extend the life of my shop vacuum. After clogging my shop vacuum filter and having to blow it out in order to restore the performance of my shop vacuum. After some research online I found the Thien Baffle and was very interested in its...

I've only been woodworking for about a year and a half, but looking back, I've accomplished quite a bit! Rather than posting each of these simple little projects in their own page, I put them all together as one "kitchen upgrade" package. All were made out of red oak, and I did my damnedest to...

Biggest, deepest thing I have turned so far. diameter on the inside is about 5", outside is about 5.5". The depth of the bowl is also right around 5" deep. It is almost 9" tall. There are some rough spots on there, but I attribute it more to the poor quality wood than anything else; my tools...

Just pine….hand cut dovetails…cut nails. Dressed the finish. Sealed with shellac than added brown shoe polish for colored wax.

I've been making buckets for about 30 years. I make other things too, but coopering is my favorite craft; blacksmithing is a close second. I started making mesquite buckets about 20 years ago, and haven't been able to stop. They're much harder to make than a pine bucket but the result is...

Mafe's wood bucket Mikes ancient bucket class I have finally done it! My bucket is completed. Quite some time ago our friend Mike asked if anyone wanted to participate in a building an ancient bucket class, I turned in and was fast hooked. To do this with Mike has for me been a process of...

I recently picked up an edge trimming plane from Veritas and decided to use it to make a bucket. This first go at making one was going to be a simple as I could make it. It wouldn't have hoops nor did I expect it to hold water. Making the beveled side pieces was rather easy with the trimmer...

Hickory Bucket; twelve tapered staves, bent wood handle and dado inset bottom. Approx 12 inches tall with poly finish. I have made many of these out of pine, cedar, oak, walnut, and hickory. Each stave is cut with the table saw set at 15 degrees and tapers from 3 inches wide at the top to 2.5...

After sitting a couple days on the bottom of a flipped over 5 gallon bucket, I knew there had to be a better way. More pics and video at my site http://www.jeff-ferguson.com/2014/11/12/homemade-5-gallon-bucket-seat/

Ye Olde Cedar Bucket When a guy gets an armload of nice western red cedar for free, you have to do something with it. I have made quite a number of these buckets over the years, but usually out of hickory, oak or walnut. This was made from cutoffs from a residing project….very nice lumber. It...

Project Description A bucket made entirely with hand tools including wooden staves reinforced with hand carved dowels, bottom also made of 3 boards also held together with hand carved dowels, and banding cut from debarked Willow tree branches to hold the whole thing together. No glue. This would...

Cedar Buckets x 3. A friend gave me a stack of cedar siding cut-offs a few months ago, so I decided to put them to good use. Earlier, I made one bucket, and now this set of three buckets used up nearly all of the rest of it. The buckets are each crafted in the same fashion….12 tapered...

This is a 3 1/2 gal pine bucket with steel hoops and a hemp rope handle-doesn't get more basic than this. The design is ancient and I don't think anyone can claim it. This is a very versatile bucket; it's light weight, water tight, nice to look at, and you can put just about anything in it. My...

I scored this Craftsman Pro Jointer on CL for 120.00 a coule months ago…. I dont have a Dust Collection System in my Shop because i dont have the power to run one! Just to run this jointer i have to make sure everything else in the shop is shut off or it trips the breaker… i cant upgrade my...