LumberJocks Woodworking Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 500 Results
  1. Projects Mantel Clock

    Decided to use up most of the pile of leftover Ash...was resawn down to ~1/4" thick. Had to glue a few "slats" up into wider panels....Base and top were not resaw...tablesaw to mill the bevels. Hobby lobby provided the clock, and the fancy feet, and the corner brackets... 1 coat of Witch's...
  2. Projects New Chest of Drawers for the Bedroom

    Frame & Raised Panel sides, drawer fronts beveled to match the raised panels. Bread Board edged Top. Stain is one coat of Witch's Brew, then 2 coats of Amber Shellac Top has 3 coats of Amber Shellac.. fancy feet, too.
  3. Projects In Progress
    At least it will keep me out of the Taverns.. These parts.. Are to become a 5 drawer Chest of Drawers....Raised panels in a Frame & Panel side...the frame is where the drawers will ride on..they also connect the sides to each other. Center strip? is where the top of backs of the drawers will...
  4. Projects Live edge shelves

    These shelves are similar to some I showed here some years ago for the living room in the cabin. This time, my wife wanted shelves in the bedroom. I used the same kind of mountain laurel brackets as before, but instead of the cheap pine shelves I used last time, I used local ash. The ash...
  5. Projects English Garden Bench

    Loosely modeled after Norm Abram's Teak English Garden bench View from one end.. Around in back.. Feet have plastic pads to keep them off of the Concrete ... Those 2 darker slats are sap wood Ash... Thanks for looking in... Note, for scale: I am making sure this will support me...Boss is...
  6. Projects Found a spot in my shop not being used.

    I have a 5/8" oil field sucker rod in the middle so it will spin around easy! |This was the last place in my shop I don't have junk and things cluttering up and this is great for it is out of the way hanging over the sink. They do get dusty but a little air every once in a while makes it back...
  7. Journal The Boxmaker

    Went through all the leftovers, resaw what I could... And what wasn't worth the effort.. Will be heading to the Fire Pit....results? Have these 3 for box lids... Have these for sides and ends...which leaves... These for another 2 boxes? Sorted out a few parts... 1/4" thick panel for the...
  8. Projects Third sister -Coffee table in ash

    EDIT: Sorry for the duplicate (triplicate?) photos. The user interface has been updated since I last posted, and I totally mangled uploading the project. I have just now tried to edit the post so that the cover photo is correct, and the unintentional photos removed…BUT I don’t seem to be able to...
  9. Projects In Progress
    PIP? Coat of Witch's Brew is drying, at the moment... And, this is what you'd see when looking under the End table....This is the back..."Fiddle Stick" along the edge, is to keep things from sliding out the back, and onto the floor... There is no metal used in this....all through dovetails...
  10. Journal Add a shelf to an End Table

    The Boss has an End Table beside HER chair. Right now, there is an ugly, lidded plastic storage tub sitting under it, as a shelf. Boss has decided the tub just has to go! It sit too high..She wants a shelf (wood, of course) to replace it! Hmmm.....measured for the new shelf....did not...
  11. Projects In Progress
    Just a few planks of Ash, and some metal parts... I even stood on it, once it was down on the shop floor... A view around in back.. ( That Cabinet back there? Holds 17 handsaws) And a view from a side... Finish is a Stain & Amber Shellac Blend, I call The Witch's Brew......
  12. Journal Ladder Repair

    Grandson dropped off a small, 2-step Stepladder that he wanted to get repaired.. The "problem" ? particle board braces....that someone had stepped on...and broke one of the back legs. I was looking for a way to use up a plank of Ash... from this $20 stack of 9 boards 1 x 6 x 6' Front one...
  13. Projects In Progress
    Unable to restock the Lumber Rack at the moment..decided to dig through some of the Left over stuff sitting around in the shop....wasn't much all that big, but.. Maybe a small box can be in there, somewhere....at least 2 sides..and a Pine bottom... These might do for the 2 ends, and maybe a...
  14. Projects Balance beam system for granddaughter

    Beams are 7/8” ash and the risers are two different heights. 2” and 1”. There are also two transition risers that have half 1” and the other half 2”.
  15. Projects Trestle Plant Stand

    Trestle Leg Plant Stand In 2018 a large ash tree was blown down in my neighbors yard. I was fortunate enough for him to allow me to have access to cut the tree up into natural edge slabs. Now that the wood is dry I made a plant stand that can be assembled as a kit for shipping. The screws in...
  16. Projects Slipper Caddy

    A small caddy to park most of the Boss' slippers on...and out of the way... Leans back to allow full access. Has carrying handles to allow it to be moved around... While the shelves are level with the floor...sides splay out at about 10 degrees.. Sides lean back a bit...there is a strip of...
  17. Projects WOODEN RAINBOW SET

    30x15cm ash rainbow set. First I made template on 10mm plywood, transfered it on ash board, cut on bandsaw, sanded on disc and oscillating spindle sander and rounded edges on router table. No finish.
  18. Journal A Caddy fo Slippers

    Still have left-overs....maybe a Project for the Boss to store all her slippers in? 1 x 6 x 6' Ash plank to the shop ( will get to the Maple one, later). Had a badly split end, cut that off, find the new center point, to make a pair of blanks... Goal was to make a "Book Matched Panel" by...
  19. Projects 4 Drawer Chest of Drawers

    4 drawer Chest of drawers, built to replace an old worn out one. Frame & Raised Panel sides, drawer fronts are raised panel look. Top has a bread board edge, and is Spalted Maple.. Front view... Drawer details, frame & raised panel sides Bread board edges.. Knob details
1-20 of 500 Results
Top