LumberJocks Woodworking Forum banner
  • Please post in our Community Feedback thread for help with the new forum software! If you are having trouble logging in, please Contact Us for assistance.

Project Information

Either Sears, Roebuck & Co. or Montgomery Ward had this piece built in South Bend, IN just after the turn of the 20th century. The page shown in the Sears catalog is from the 1904 edition. I believe this is the Motgomery Ward cabinet.
The cabinet was seriously abused by all the former owners and was heavily coated with nine coats of badly applied paint of various colors. I gather the first finish was a thinly applied, colored varnish over the maple/poplar wood used to make it. The joinery was decently done but no glue or screws were used, not even where dowels were used and the joints at the corners and dado joints were NAILED! Seriously!
Much of the wood was worn out, especially the drawer sides where they slid against the cabinetry. Some parts had to be replaced with carefully copied woodwork.
The original work top was gone. In its place was poplar planks nailed onto the casework and covered with old, oil based linoleum.
Since my wife wanted a French Country theme in the kitchen, and since the woodwork in the cabinet was so dinged and dented, we painted it a buttery yellow with an antique looking blue trim. I added some scrollwork fancies on the sides of the topper because I felt it was too plain.
The ugly work top replacement was tossed out and a beautiful, custom made piece of granite was used instead.
One of the legs was unusable and a new one was made and then new ends were made for all four of them. They were designed to fit plastic low friction slider pads and made wider to spread the, now heavier, weight of the unit.
New die cast, nickle plated hinges were installed on the doors.
Low profile electrical receptacles were installed in the back panel.
It took most of a Summer and Autumn to do the work.
I'm happy with it and, most importantly, She Who Buys Me Tools is pleased.

Gallery

Comments

·
Registered
Joined
·
129 Posts
Beautiful cabinet! I'll bet that looks fantastic in your kitchen.

There was a similar cabinet in my parent's basement when I was growing up, and it hadn't been terribly abused. Unfortunately, the basement got five feet of water from Hurricane Agnes in the early 1970s and the cabinet just crumbled. The only thing that we salvaged from the basement was a six-foot-long wood chest that had been in my grandparent's kitchen when my father was growing up. The lids show the wear of children's butts since dad and his brothers used it as their seats at the table. That chest is now in my dining room.
 

·
Registered
Joined
·
746 Posts
That my friend is STUNNING! My wife also likes that type of thing. I'm no letting her see this.:)
 

·
Registered
Joined
·
577 Posts
wow, heck of a restoration! :)
 

·
Registered
Joined
·
386 Posts
if she's happy….all LJ's are happy! :)
 

·
Registered
Joined
·
39 Posts
Wow, I bet it's worth more than the $8.95 price in the catalog! Do you have any pictures from before the restoration?
 

·
Registered
Joined
·
4,296 Posts
Very nice restoration.

Welcome to LJs.

CtL
 

·
Registered
Joined
·
1,113 Posts
I'm embarassed to admit, I didn't take any "before" photos.

Boy, do I feel stupid!

d
 

·
Registered
Joined
·
18,890 Posts
oh to have this in my kitchen!!!!!
 

·
Registered
Joined
·
957 Posts
Ms Deb, I've got a oak kitchen Hoosier with flour sifter and frosted pattern glass doors. It needs to be refinished, but the good part is that it was never painted. Someday I need to either refinish it or sell it, it's been sitting in the basement for 20 years. I have another one that is oak and was painted and not quite as nice that I refinished back down to the bare wood, stained, and finished about 15 years ago, that sits in the kitchen now. I guess the reason I never got around to refinishing the other one is I want to do it when I feel comfortable enough to do it without damageing the frosted glass. I have refinished alot of old furniture over the years, so it's not that refinishing is the problem.
 

·
Registered
Joined
·
6,058 Posts
you have a kitchen Ms Debbie well I wish I had a kitchen my wife cooks out of an old cardboard box.Alistair
 

·
Registered
Joined
·
1,456 Posts
Beautiful work Don, I like the old toaster on the top it fits nicely. Exactly how many tools is a restoration like that worth to the wife?
 

·
Registered
Joined
·
1,113 Posts
Woodchuck,
I know the illustration in the catalog looks like oak, but the actual unit is maple where it shows and poplar inside and underneath.
Refinishing furniture with glass parts shouldn't be any different from other refinishing projects. Just remove the glass first. Look carefully in the back of the glass where it's fastened. Variously you may find clips, moldings or whatever that can be gently removed. In the rare case where the glass was glued in with caulk, it needs to be cautiously sliced with a sharp carton knife. Work slowly and be careful. In the event that the glass breaks, a good glass shop will be able to match it with new stuff.
If you can, take a close up photo of the glass where its fastened in and post it here. I think many of us would be able to give some good advice about removing it.
Paul,
Marge buys me tools all the time. If she bought me another major tool I'd have to sell something to make room for it.
Remember, the Outback has to be garaged EVERY night! ;-)


d
 

·
Registered
Joined
·
957 Posts
The glass is held in with 1/4" oak molding, nailed. I know it's probably going to be a slow process, but then again maybe not, I don't know yet. But I do know that the glass would be fairly expensive to replace, there is a pattern that is etched into the glass, and if I can't get one panel of glass to match perfectly, color also, then I'm pretty much committed to replaceing all 4 panels.
 

·
Registered
Joined
·
18,890 Posts
Woodchuck.. be still my heart!
I saw a cabinet at an antique store. The wanted $1200 for it.

Scotsman: I count my blessings every day.

This is a cabinet that I do have. It was my parents (when they had only boxes for a kitchen). It's really "cheap" but it's family history. It was cut in half at one point and has been in my basement for years. When I started gathering antique items for my kitchen I brought it up from the basement and cleaned it up as best as I could.



If only I had donbee's skills to rejuvenate it.
 

·
Registered
Joined
·
402 Posts
I have refinished a few these in my career, and you did a great job on this cabinet. most of the one's I have had the pleasure of working on have been in bad repair much like the one you have. nails holding joints together glue on top of glue, and many coats of paint. rusted flour bins and hardware. but I manage to bring all but one of them back from the edge. the one I didn't still gets used as a plant stand by my in laws and they love in its present state. Once again, fine job, they are alot of work to restore but well worth the effort.

Joey
 

·
Registered
Joined
·
1,113 Posts
Debbie, Don't be afraid of it, you can do it!
Take apart what comes apart and reglue or refasten whatever came apart but shouldn't have.
Then strip or sand the old finish and put on new stuff. It really is as simple as I just said.
Having said that, I do emphasize that making new wood parts may be beyond your skill level, but find someone to partner with for that.
I feel very strongly that this project is very do-able.
Jump in there, Debbie!
Just do it!
Best regards,
Don
 

·
Registered
Joined
·
18,890 Posts
Well thanks for thinking that I can do it….. I'd be so afraid of it all falling apart.
 

·
Registered
Joined
·
1,113 Posts
Well, if it all falls apart, believe it or not, THAT'S GOOD!
Howcome?
You will then have the opportunity to put it all back together again with fresh glue. It will be like a new piece, then.
Come on Debbie, don't let this hunka wood buffalo you!

d
 
Top