LumberJocks

All Replies on Triggered Saw Stop Brake on a Dado - How to Tell if there is Blade Damage?

  • Advertise with us
View chris8's profile

Triggered Saw Stop Brake on a Dado - How to Tell if there is Blade Damage?

by chris8
posted 07-30-2017 12:54 AM


11 replies so far

View firefighterontheside's profile

firefighterontheside

21189 posts in 2710 days


#1 posted 07-30-2017 01:09 AM

Try here for new cutters. Not sure if it’ll be cheaper.
http://freud-tools.stores.yahoo.net/freuddadrepp.html

-- Bill M. "People change, walnut doesn't" by Gene.

View Rich's profile (online now)

Rich

5887 posts in 1443 days


#2 posted 07-30-2017 01:11 AM

At least you know it works. I’d say that if the blade looks fine and cuts well, keep using it.

-- Half of what we read or hear about finishing is right. We just don’t know which half! — Bob Flexner

View oldwood's profile

oldwood

162 posts in 2098 days


#3 posted 07-30-2017 02:41 AM

I have reused several regular blades with no problems, and I think yours will be alright also. Just inspect carefully for missing carbide tips or bent teeth. I expect the instruction to replace the blade is just a liability precaution by Sawstop.

View Gripbd's profile

Gripbd

21 posts in 1646 days


#4 posted 07-30-2017 02:59 AM

Reading this post raised another question in my mind. A good friend of mine recently mangled his thumb in his table saw because he got careless after he turned the saw off, but the blade was still spinning. Does the Sawstop brake work if the saw has been turned off?

View Firewood's profile

Firewood

1301 posts in 2488 days


#5 posted 07-30-2017 03:12 AM

The safety system is still active after power is shut off until the blade is fully stopped.

I would take the blade to a reputable sharpener. They will typically give the blade a good inspection for cracked or chipped teeth. Notify them of the brake incident. They should be able to inspect it more closely for any damage.

-- Mike - Waukesha, WI

View Rich's profile (online now)

Rich

5887 posts in 1443 days


#6 posted 07-30-2017 03:19 AM



The safety system is still active after power is shut off until the blade is fully stopped.

I would take the blade to a reputable sharpener. They will typically give the blade a good inspection for cracked or chipped teeth. Notify them of the brake incident. They should be able to inspect it more closely for any damage.

- Firewood

I think that’s good advice. I worried as I posted my reply that a loose tooth could cause problems.

-- Half of what we read or hear about finishing is right. We just don’t know which half! — Bob Flexner

View Putttn's profile

Putttn

133 posts in 3132 days


#7 posted 02-27-2019 02:50 AM

Resurrecting a old post and I experienced a triggered brake on my single blade and also cannot see any damage to the blade. Did you reuse yours and did it work ok?

-- Bill eastern Washington Home of beloved ZAGS

View moke's profile

moke

1593 posts in 3630 days


#8 posted 02-27-2019 03:33 AM

I know this is an old post…. I missed it originally….I had a friend have exactly the same problem….a Freud dado blade…....he told me that he found out that freud 8” dado blades are notorious for being out of round. He told me because he and I both bought our blades at the same sale probably ten years ago. I had used it frequently on a previous table saw, but always felt it was a PITA to change the cartridge after I got my SS. Since then, I have just gone next door and used a neighbors Craftsman TS. ( I sold it to him originally for a good price)

Anybody else know any more about this?

-- Mike

View Fred Hargis's profile

Fred Hargis

6428 posts in 3347 days


#9 posted 02-27-2019 11:46 AM

First time I’ve ever heard of Freud dado sets being out of round. Even if they came that way from the factory, the first sharpening (by a quality sharpening service) should true everything up. I’ve used my set on a SS for 3 years now without a problem. It would be an easy thing to check by rotating the blades while on the saw, and watch a straight edge put against the teeth. BTW, I found a sweat spot in the cartridge adjustment that allows me to change cartridges and blades between the dado set and the combo where I don’t have to adjust the clearance….maybe I’m just lucky this one time.

-- Our village hasn't lost it's idiot, he was elected to congress.

View Blindhog's profile

Blindhog

164 posts in 1902 days


#10 posted 02-27-2019 02:13 PM

I triggered the stop using a forrest dado king (8”) without any damage. It seemed to cut just fine after and this was verified when I sent it in fir sharpening.

-- Don't let perfection get in the way of plenty good enough

View pottz's profile

pottz

11305 posts in 1838 days


#11 posted 02-27-2019 03:32 PM

i have a set of freud dado blades and have no issues with them being out of round.bought the set about 6 months ago.

-- working with my hands is a joy,it gives me a sense of fulfillment,somthing so many seek and so few find.-SAM MALOOF.

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com