LumberJocks

All Replies on Separating Laminated Plywood

  • Advertise with us
View BareFootWoodworks's profile

Separating Laminated Plywood

by BareFootWoodworks
posted 07-21-2017 07:30 PM


7 replies so far

View Kazooman's profile

Kazooman

1346 posts in 2431 days


#1 posted 07-21-2017 08:06 PM

You didn’t give the size of the sign or the thickness of the plywood, so we will have to guess a little. I think you are on the right track You would need a saw with a long enough blade, but with some careful effort you should be able to split the sign in two. My best thought on removing the remainder of the mess would be with a router and a router sled. You could remove the junk and at the same time create a flat surface for re-gluing the faces to a new substrate.

View Loren's profile

Loren

10477 posts in 4127 days


#2 posted 07-21-2017 09:25 PM

I can’t think of any reasonable solution
to the problem that doesn’t entail
a risk of damaging the sign.

This is a difficult client-relations issue.
Probably the lowest risk is to buy a
hand saw with the capacity you need
and go to work on it. You’ll need to
remove the remainder as Kazooman
suggests. I hope your client is paying
you fairly for your time because it
sounds like a real pain to do the job.

You can make one or more hardwood
wedges and try to split the plywood in
half. This could be reasonably quick to
do but could damage the face boards.

You could rip the sign into sections on
the table saw and reassemble it later with
those sections still separated by the
kerf width. This approach would make
removing the plywood with the table saw
feasible. It would also be reasonably quick
and you could plane the plywood off
without going to the effort of making an
using a router jig to do it.

Finally, if you steam the plywood it may
eventually crack open on its own.

View BareFootWoodworks's profile

BareFootWoodworks

6 posts in 789 days


#3 posted 07-23-2017 01:38 AM

!https://s3.amazonaws.com/vs-lumberjocks.com/otiryrd.jpg

Thanks for the suggestions!

I ended up spending about two hours to separate the two faces. At the same time I discovered that the faces where molded in plaster and inlaid in plywood, to make the two faces, and the center lamination was some high grade plywood from 30 years ago. Might I add that this sign is most likely just older than I am, lol. I wish I would have taken a picture of how I actually started it. I started but using a chisel and tapping it in about two inches around the entire thing to create a score line I could wedge into. I then used a good portion of my collection of standard screw drivers to tap into my score like I was try to split a large piece of stone. Evenly tapping each one in succession. However, I ran out of screwdriver pretty quickly and it had not separated nearly enough, so I ran down the big orange box store and grabbed some pieces of 2’ rebar and used my angle grinder to make a large metal wedge. And, I was pretty surprised when it actually worked without cracking the plaster. I only really realized the faces we’re part plaster after it was separated and could see the plaster. The sign had been painted so many times over the years that there is about 3/16ths of an inch of paint on it. Before I started working on this sign, I had told the gentleman who commissioned me I would save it if I could but if I couldn’t I could make another replica because it’s for a historic building. So all in all I just have to find someone really nice exterior plywood round where I live and it should be good as new. The dimensions are 37×26x3.5.

-- ~That Guy~

View BareFootWoodworks's profile

BareFootWoodworks

6 posts in 789 days


#4 posted 07-23-2017 01:39 AM

-- ~That Guy~

View AlaskaGuy's profile

AlaskaGuy

5338 posts in 2788 days


#5 posted 07-23-2017 02:10 AM

I’m glad I’m 73 and retired. Now if it ain’t easy I don’t take on the job. :) Not to say I don’t like a challenge I just want to pick my challenge

-- Alaskan's for Global warming!

View Kazooman's profile

Kazooman

1346 posts in 2431 days


#6 posted 07-23-2017 03:10 AM

Glad to hear that you got it apart. The rebar wedges were a great idea.

In the picture I see a round sign but you gave rectangular dimensions, so I am a bit confused. If it is a rectangle, I was wondering if it might be a good idea to make the plywood piece smaller and wrap it with some hardwood edging. That might help keep water out of the plies.

How about a nice pic of the final outcome when you are done?

View BareFootWoodworks's profile

BareFootWoodworks

6 posts in 789 days


#7 posted 07-23-2017 05:00 AM

It’s an oval sign, so it’s the best of both shapes and I’ll be glad to post a snap shot of it all back together.

-- ~That Guy~

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com