All Replies on Casters vs Mobile Base??

  • Advertise with us
View Jenine's profile

Casters vs Mobile Base??

by Jenine
posted 07-08-2017 08:25 PM

8 replies so far

View Woodknack's profile


13463 posts in 3225 days

#1 posted 07-08-2017 08:52 PM

Is your floor dead flat? If it isn’t and you go with casters, it could twist the frame.

-- Rick M,

View Jenine's profile


146 posts in 2568 days

#2 posted 07-08-2017 08:56 PM

I doubt it, it’s a garage so it should slope. Good point though…didn’t think about that. If I add washers to level it, would that solve the problem? Although, I suppose it would depend on where it is each time I use it. Hmmmm.

-- - Montana sucks. Tell your friends.

View Loren's profile


10565 posts in 4493 days

#3 posted 07-08-2017 09:25 PM

Leveling casters work for machinery.

Regular locking casters have some deficiencies
that make mobile bases generally preferable.

View jonah's profile


2124 posts in 4143 days

#4 posted 07-08-2017 10:07 PM

Even when locked, there is a lot of slop in casters that makes them less than ideal IMO. The best case is a mobile base where all four wheels pop up and the thing rests on solid feet when in stationary mode.

View bigJohninvegas's profile


802 posts in 2307 days

#5 posted 07-08-2017 10:23 PM

There are castors for machinery like Loren points out, but I agree with Jonah about there being slop even when they are locked. The moble bases out there are proven to work well. I have built a moble base for my drill press. Cheap clunky castors with no locks that actually worked well for that application. I put good locking castors under a work bench. Huge mistake on my part. Could not keep that bench from racking. I would be afraid of my table saw moving while I am trying to use it.

-- John

View Planeman40's profile


1516 posts in 3606 days

#6 posted 07-09-2017 08:24 PM

I have put casters under almost all of my machines as I am getting tight on space and have moved some of my less used machines to a “parking” area in the shop. I just roll them out when needed. Personally, I find they work just fine, even beneath my 850 lb Hammer 48”x 48” sliding table saw. I have no locking casters. I find the weight of the machines keeps them from moving on my relatively level concrete basement floor. I purchased all of my casters from Harbor Freight, making sure I bought the better grades of casters. They work great.

My position is, if you are putting enough pressure against the work when feeding it to move the machine, you are doing something very wrong. I never have a problem with any of the machines moving when working.

-- Always remember: It is a mathematical certainty that half the people in this country are below average in intelligence!

View ohtimberwolf's profile


1009 posts in 3197 days

#7 posted 07-09-2017 08:48 PM

Here is something you may want to consider. larry

-- Just a barn cat, now gone to cat heaven.

View AZWoody's profile


1478 posts in 2069 days

#8 posted 07-09-2017 08:56 PM

Another benefit of mobile bases is they are more stable then casters as they spread the footprint a little wider than the machine.
Whether pop up, or feet that screw down to stabilize the machine, I have always preferred them to anything I’ve had on casters.

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics