All Replies on Combination Square with All 1/16" Graduations

  • Advertise with us
View pintodeluxe's profile

Combination Square with All 1/16" Graduations

by pintodeluxe
posted 01-26-2017 01:27 AM

13 replies so far

View CharlesA's profile


3395 posts in 2410 days

#1 posted 01-26-2017 01:34 AM

That’s interesting that you don’t like 4R. While I don’t use the 1/64” much either, I like the other 3 Rs.

-- "Man is the only animal which devours his own, for I can apply no milder term to the general prey of the rich on the poor." ~Thomas Jefferson

View pintodeluxe's profile


6041 posts in 3425 days

#2 posted 01-26-2017 01:37 AM

It’s just as easy to split the 16th marks. Most measurements in woodworking are relative anyways. Consistency is often more important than absolute accuracy. I actually design projects with 1/8” dimensions, so that upon dividing you are still only dealing with 1/16” increments.

I would rather not have to re-orient to a new scale every time I flip the square over. Somewhat aggravating.

-- Willie, Washington "If You Choose Not To Decide, You Still Have Made a Choice" - Rush

View PPK's profile (online now)


1646 posts in 1421 days

#3 posted 01-26-2017 02:13 PM

Pinto, I really don’t have any idea – I’m in the very same boat – I’d like a 1/16ths scale only. I was about to drop the money for a PEC, just like the one you pictured on top. Currently I only have a Empire “square” that isn’t square. I’m getting to the point that I think being aggravated by having to find the right side of the rule for the desired tick marks is going to be better than dealing with non-square lines…

I noticed that Lee Valley had a set of Non-Starret combo squares that looked to be better than your box store kind, and I was going to check them out, but they were some promo or something, and now they aren’t available anymore :(

-- Pete

View Ken90712's profile


17820 posts in 3801 days

#4 posted 01-26-2017 08:25 PM

Its crazy how much we can spend on these. With that said I found once I bought my Starrett I was in love. I’m also a big fan of the Incra products, both of these are more accurate than myself. LOL

-- Ken, "Everyday above ground is a good day!"

View Bill White's profile

Bill White

5243 posts in 4572 days

#5 posted 01-26-2017 08:37 PM

Use a marking knife. That way ya don’t have to worry about minute increments.
Oh, get good glasses. :)

-- [email protected]

View HokieKen's profile


12043 posts in 1751 days

#6 posted 01-26-2017 08:48 PM

All of my combo squares are 4R. I use the 32 scale almost exclusively. I did a little looking and didn’t find anything with only 1/16 scales. Not sure where you might find such a thing. Good luck though!

-- Kenny, SW VA, Go Hokies!!!

View RobS888's profile


2635 posts in 2457 days

#7 posted 01-26-2017 09:04 PM

This says only 1/16th….

Don’t know if I would trust the squareness, but you could use your current head with the rule portion.

-- I always knew gun nuts where afraid of something, just never thought popcorn was on the list.

View DirtyMike's profile


637 posts in 1514 days

#8 posted 01-26-2017 09:07 PM

stay away from empire if accuracy is important to you.

View ajshobby's profile


103 posts in 2920 days

#9 posted 01-27-2017 12:24 AM

Any of the big orange squares can work if you dig through them to find a decent one. I have a starret and they are the best. I stumbled across a mitioyto combo square a few years ago and I now buy them for work. Half the price of starret with all the same quality.

AJ in mpls.

View Roger's profile


21030 posts in 3416 days

#10 posted 02-17-2017 04:43 PM

I have a Pinnacle from Woodcraft that I purchased quite a few years ago when it was on sale. Don’t remember what I gave, maybe 50 or 60 bux. Too many of our badly needed tools seem to always be over-priced, in my opinion.

-- Roger from KY. Work/Play/Travel Safe. Keep your dust collector fed. [email protected]

View mramseyISU's profile


578 posts in 2157 days

#11 posted 02-17-2017 04:51 PM

In all seriousness go to Home Depot and look at the Empire squares. They’re guaranteed good to .005” and everyone I’ve checked is dead nuts square. I am concerned about how long the aluminum head will wear compared to a steel or iron one by so far I have no complaints with them.

-- Trust me I'm an engineer.

View pintodeluxe's profile


6041 posts in 3425 days

#12 posted 02-17-2017 06:09 PM

The Empire square is what I’m starting with. I buy one every year or two, as they tend to go out of square. The current one is intermittently square, and certainly not good enough for exacting work.

I recently ordered two Woodriver 12” squares. The first one had a manufacturing blem and wouldn’t slide. The second one wasn’t square (off by nearly 1/8” at full length). So I returned them.

I also looked at the Pinnacle, and 8 out of 10 reviews said it broke in the same place. Apparently it is a weakness with that brand / model.

I had high hopes for the iGaging square, because I really like some of their products. My 6” iGaging double square is okay. It doesn’t slide very nicely, but at least it is square. The markings on one side are impossible to read.

I guess I’m stuck with getting a Starrett and those fine markings on one side.

-- Willie, Washington "If You Choose Not To Decide, You Still Have Made a Choice" - Rush

View PPK's profile (online now)


1646 posts in 1421 days

#13 posted 02-17-2017 06:51 PM

I just bought this one, and have been using it for a couple weeks now:

It is a true PEC square, and is dead on. The graduations are very well etched, and it slides OK. Really don’t care if it doesn’t slide super easy, as long as its square! For the price, you can’t beat the quality…

-- Pete

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics