LumberJocks

All Replies on Circular Saw Blade for 2-in Butcher Block

  • Advertise with us
View seadonkey's profile

Circular Saw Blade for 2-in Butcher Block

by seadonkey
posted 01-24-2017 09:40 PM


8 replies so far

View Carloz's profile

Carloz

1147 posts in 977 days


#1 posted 01-24-2017 10:03 PM

Why do you care about being slow ? Are you going to spit out five butcherblocks per hour and if affects your paycheck ? About burning, you will need to sand down the edges anyway so why bother. It is much more difficult to deal with tearout.

View seadonkey's profile

seadonkey

13 posts in 874 days


#2 posted 01-24-2017 10:21 PM

I don’t care about production speed, of course. :-) I was just concerned about burning due to the slow cut speed, but that is easier to remedy than tear out

-- I mostly make firewood...

View wuddoc's profile

wuddoc

346 posts in 4104 days


#3 posted 01-24-2017 10:41 PM

Why not cut less than the 2” off on first pass to determine speed and if wood burns with 60 tooth blade.

-- Wuddoc

View bigblockyeti's profile (online now)

bigblockyeti

5742 posts in 2107 days


#4 posted 01-24-2017 10:42 PM

What size circular saw will you be using for ththis task?

-- "Lack of effort will result in failure with amazing predictability" - Me

View JBrow's profile

JBrow

1368 posts in 1306 days


#5 posted 01-25-2017 02:34 AM

Seadonkey,

The orientation of the cut dictates the type of saw blade. For example, if the width of the butcher block is trimmed by cutting a little off a long edge (the cut line parallel to wood grain) or the butcher block is an end grain butcher block (regardless of the edge to be trimmed), a rip blade would be a good choice. On the other hand, if this is not an end grain butcher block and the end will be trimmed (the cut will be across the wood grain), a crosscut blade would be my choice. I would expect the best results from a quality rip or cross cut blade that is brand new (that is very sharp) and carbide tipped. For a rip cut, a new 24 tooth rip blade and for a cross cut, a new carbide tipped 60 tooth seem good choices.

I like the idea proposed by wuddoc; make an initial practice cut, leaving an inch or so for the final trimming. The practice cut will give you a feel for the saw and the blade as it cuts through the material. After the practice cut, the final trimming can be performed. The final trimming could be a two cut process, in an effort to reduce any burning of the wood. The first cut would leave the butcher block perhaps 1/8” –3/16” too big and could leave some burn marks on the wood. The final skim cut would be set up to produce the size you are after and would remove very little material and any burn marks. The saw blade should run cooler and reduce burning during the skim cut.

As Carloz mentioned, tear out (fraying along the cut line) may be a problem. Since a circular saw blade enters the cut from the top surface, tear out can occur on the bottom face. Applying some masking tape (not painters tape) all along and centered on the cut line on the bottom surface of the butcher block, ensuring it is firmly in place, can help support the wood fibers during the cut and reduce tear out.

A butcher block that is light in color and bought at a store is likely to be hard maple. This seems to be a popular wood for butcher blocks sold by retailers, probably because it is a very hard (dense) relatively inexpensive wood. But from where I am sitting it is difficult to say for sure what wood you have.

View MT_Stringer's profile

MT_Stringer

3183 posts in 3617 days


#6 posted 01-25-2017 02:45 AM

I have a 7 1/4 inch Diablo 60T blade in my circular saw. It works great

Got it at the big orange box store.
http://www.homedepot.com/p/Diablo-7-1-4-in-x-60-Tooth-Fine-Finish-Saw-Blade-D0760R/100627136

-- Handcrafted by Mike Henderson - Channelview, Texas

View seadonkey's profile

seadonkey

13 posts in 874 days


#7 posted 01-25-2017 03:03 AM

Thanks so much for the advice fellas! I went with the two cut advice and a 60 tooth blade and it worked great.

Thanks again! And be prepared for more dumb questions in the future

-- I mostly make firewood...

View Carloz's profile

Carloz

1147 posts in 977 days


#8 posted 01-25-2017 08:35 PM


I have a 7 1/4 inch Diablo 60T blade in my circular saw. It works great
Got it at the big orange box store.
- MT_Stringer

From recently the biggest orange store is Amazon, and it also became a box store at least in my city.

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com