All Replies on Replacing jointer feet with caster wheels?

  • Advertise with us
View Dagobah's profile

Replacing jointer feet with caster wheels?

by Dagobah
posted 09-13-2016 04:51 PM

14 replies so far

View splintergroup's profile


4042 posts in 2102 days

#1 posted 09-13-2016 06:59 PM

I made a mobile base for my Jet 6”.
If I had it to do again, I’d do it differently.

My problem is even with locking casters, they still ‘wiggle’ around. I’d be better off replacing the two casters on one end with non-swivel wheels and the casters on the opposite end with feet.
To move it around, just lift the end with the feet, much like pushing around a wheelbarrow. When set back down, it should be stable.

View syenefarmer's profile


561 posts in 3960 days

#2 posted 09-13-2016 07:16 PM

The Ridgid 6” jointer is very top heavy. I would think that just putting casters on the stand legs would invite a tip over the first time the wheels hit an obstruction on the floor. You’d be better off putting the casters on a wider piece of plywood and then bolting the jointers legs to the plywood.

View BorkBob's profile


127 posts in 3572 days

#3 posted 09-13-2016 07:55 PM

My 8” jointer has built in tricycle wheels. I park it against a wall and it was a hassle to get it out in the open. I set it on I’m tall so the added height is not a problem.

-- Please Pray for Our Troops / Semper Fi / Bob Ross /

View MT_Stringer's profile


3183 posts in 4110 days

#4 posted 09-13-2016 08:00 PM

My 6 inch Jet came with a mobile base. Two casters are fixed and a third swivels. Yep, at times it can move around when I am working it hard.

-- Handcrafted by Mike Henderson - Channelview, Texas

View Kirk650's profile


680 posts in 1628 days

#5 posted 09-14-2016 01:18 AM

Everything in my workshop has wheels except for the jointer. I carefully chose where to put the jointer and have never had to move it. I do move other wheeled apparatus to allow room to use the jointer with long boards. I even had to open the front door one fall weekend to allow room to run 7 foot bed posts over the jointer.

View lennyk's profile


34 posts in 1711 days

#6 posted 09-14-2016 01:26 AM

Have same 6” ridgid 200lb
i welded up a base out of 1 1/2” angle steel and put hf wheels on them. Two straight and two swivel.
The two straight are on the out feed side.
I usually just stick a piece of 1/2” rod under the wheels to jam them.

View Picken5's profile


323 posts in 3571 days

#7 posted 09-14-2016 03:52 AM

I’ve tried lockable casters a few times and they didn’t work for me. The tool rocked a bit which I found annoying. And sometimes one of the locking casters would come unlocked at inconvenient times. So I got a mobile base for my older 6” Delta jointer a few years back. No regrets at all. It installed easily and works great. If I recall, it was an HTC that was rated at 500 lbs. I think my jointer weighs about 250 lbs which is probably pretty close to what your Rigid jointer weighs.

-- Howard - "Time spent making sawdust is not deducted from one's lifetime." - old Scottish proverb

View Holbs's profile


2366 posts in 2909 days

#8 posted 09-14-2016 04:03 AM

i went mobile base. $55… was an easy decision.

-- The Carpenter Bee is derived from the Ancient Greek word wood-cutter "xylokopos/ξυλοκὀπος"

View lennyk's profile


34 posts in 1711 days

#9 posted 09-14-2016 11:02 AM

wheels are great for everything, my stuff is all outdoors so every week I push everything aside and
hose down the floor.

View OggieOglethorpe's profile


1276 posts in 2989 days

#10 posted 09-14-2016 01:03 PM

A few wedges can lock anything in place, wheels or not…

Roll it into place, tap them in, nothing is going anywhere until you take them out.

View PaulHWood's profile


467 posts in 3132 days

#11 posted 09-14-2016 02:05 PM

I started with that and did not like it as the base is very flexible. I used a harbor freight kit, some steel tubing (stolen form another LJer), and a plywood base that I could bolt the jointer too.

-- -Paul, South Carolina Structural Engineer by trade, Crappy Woodworker by choice

View BinghamtonEd's profile


2298 posts in 3249 days

#12 posted 09-14-2016 02:12 PM

When I got my old 8” Yates jointer back to my garage, I put it on a HF furniture dolly as a temporary place until I made/purchased a mobile base for it. It still sits on that dolly, and I chock the wheels with scrap when I wheel it out for use.

-- - The mightiest oak in the forest is just a little nut that held its ground.

View HokieKen's profile


15157 posts in 2018 days

#13 posted 09-14-2016 03:32 PM

I made a “dolly” out of 2×4s and plywood and put double locking casters on it. Casters are great but the narrow footprint made it too unstable. So, I made some wedges that I put under the dolly when I’m using it and it works great.

-- Kenny, SW VA, Go Hokies!!!

View splintergroup's profile


4042 posts in 2102 days

#14 posted 09-14-2016 08:21 PM

A few wedges can lock anything in place, wheels or not…

Roll it into place, tap them in, nothing is going anywhere until you take them out.

- OggieOglethorpe

I use some thin cutoff strips as wedges (about 1/4” x 1/4” triangle). It works, but a major hassle. A swing-down wedge or other movement stopping device would be better. If it isn’t convenient to use, I find myself not using it.

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics