LumberJocks

All Replies on Analysis Paralysis

  • Advertise with us
View GVC66's profile

Analysis Paralysis

by GVC66
posted 09-08-2016 03:17 PM


7 replies so far

View Robert's profile

Robert

3397 posts in 1868 days


#1 posted 09-08-2016 03:33 PM

What kind of joinery? If its M/T a power mortiser is the best option IMO.

I’ve never seen the value in guys spending > $6-800 (or more) for a fence and lift, and that doesn’t even include another $300 for a router.

I’d be looking at a shaper if I did that much router work.

So yeah, I would be paralyzed, too. ;-)

-- Everything is a prototype thats why its one of a kind!!

View Rentvent's profile

Rentvent

151 posts in 1236 days


#2 posted 09-08-2016 04:39 PM

I’m leaning towards this router table

Plus this router

The triton router has a built-lift mechanism and comes with a handle to adjust from the top of the table. the collet also locks when extended above the table. You only need one wrench (and one hand) to change bits.

View MadMark's profile

MadMark

979 posts in 1840 days


#3 posted 09-08-2016 04:49 PM

I have a Grizzly G0715P with the Incra & a 3-1/2 hp Milwaukee plunge router. No router lift needed since the normal router depth knob works well. It is an outstanding setup.

M

-- Madmark - [email protected] Wiretreefarm.com

View GVC66's profile

GVC66

4 posts in 1013 days


#4 posted 09-08-2016 05:33 PM

Wow, that was quick! Thanks for the responses so far. I have looked at going the shaper route but I am not running production and will likely be using the table for a host of different projects so.. the cutters, shaper, space loss, and lack of flexibility was what doomed the shaper in my hobby shop. ( I am not even going to have the space for the LS52TS, I will need the LS32TS. )

I am leaning toward the following from Incra:
LS32TS
Mastr Lift II
Clean sweep
1000HD
Wonder Fence
Shop Stop
Right angle fixture

and the following from Excalibur (aka General):
40-070EK Cast Iron Table (Bench or Table Saw Wing) Kit (looks like the plate and fence are gravy on the kit at 399)

View 01ntrain's profile

01ntrain

259 posts in 1457 days


#5 posted 09-08-2016 06:03 PM

You never said what type of router that you’ll be using.

If I was starting from scratch, I would consider the Triton TRA001. With it, you wouldn’t need a router lift.

View GVC66's profile

GVC66

4 posts in 1013 days


#6 posted 09-08-2016 06:08 PM

01ntrain, That is interesting, I think that may be the same one rentvent was looking at. I have a couple P&C routers but nothing 3.25 horse or better. I’ll look into it. Thanks!

View bkseitz's profile

bkseitz

295 posts in 1697 days


#7 posted 09-09-2016 01:24 PM

I started out small, then upgraded with add-ons. On it is an Exaktor sliding table, Mule 50” fence system, an overhead DC/Guard from PSI, and a Incra 1000HD. Unless my Contractor TS dies its unlikely I’d upgrade any more. As it seems to handle most everything and quick frankly is more accurate than my current skill level.

The TS-LS looks good but seems a bit complicated to operate from my perspective. Not owning one take my advice on its operation with a grain of salt.

I’ve a Mast Lift II R with a PC 3.25hp router and a Woodpecker SuperFence with microadjuster. Just finishing building out the cabinet. This is replacing a Craftsman Router Table and Prof Router 2Hp. Expect this will last a lifetime. Like the easy setup with a raiser. I didn’t see the need for a clean sweep as I was building a cabinet—loosely based upon Kreg cabinet plans—that included a dust collection section as well as storage for bits and accessories.

-- bkseitz, Washington "if everything is going well, you've obviously overlooked something"

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com