All Replies on End Grain cutting board lines

  • Advertise with us
View willhime's profile

End Grain cutting board lines

by willhime
posted 09-06-2016 06:57 AM

7 replies so far

View Arcola60's profile


108 posts in 3263 days

#1 posted 09-06-2016 07:44 AM

End grain will tear out. I have tried different bits, changed speeds and feed rates. It will happen. I could not get away from it. I finally built a V-Drum sander. That has changed my sanding time drastically. It took about 3 hours off of the sanding time, for me. I found that the Klingspor hook and loop paper holds up the best. I will not run End grain in a planer. I now some woodworkers do. That is a personal decision that we all have to make.

Ellery Becnel

View jmartel's profile


9069 posts in 3030 days

#2 posted 09-06-2016 01:49 PM

What grit are you sanding with? Start with no higher than 80 grit and you should get those lines out with a bit of sanding. Go slowly over the entire board rather than focusing on the lines or else you will get the divots you are experiencing.

-- The quality of one's woodworking is directly related to the amount of flannel worn.

View Rick  Dennington's profile

Rick Dennington

7008 posts in 4074 days

#3 posted 09-06-2016 03:12 PM

I’ve never used a router-plane so I don’t know anything about those. I have made a few boards, but mostly long grain. I’ve made about 3 end-grain boards, and have run them through the planer…One board flew apart, but I didn’t use enough glue (I think) on some of the glue-ups, and “starved” the wood (that was my fault). But the other ones come out nice and smooth, so I finished them with 220-320 paper, then used a finish sander with 600-800 grit for the final sanding….One thing’s for sure….long grain is much easier than end grain to work….If you have one, try using a finishing sander with a higher grit, and see what that does for you….

-- " There's a better way.....find it"...... Thomas Edison.

View Paul Mayer's profile

Paul Mayer

1134 posts in 3945 days

#4 posted 09-06-2016 03:45 PM

If you are sanding for 2 hours and still seeing marks, I’d suggest skipping the router and just start with a hand held belt sander. If you do a good job on your final glue-up (and that is the key more than anything else), you should be able to sand your way to a finish-ready surface using a hand-held belt sander with 60 grit, working your way up through a random orbital sander with 180 grit, in about a total of 20 – 40 minutes on an 16” square end grain cutting board, depending on species and the power of your sanding equipment. As you mention, softening the end grain with water also helps to speed this up.

-- Paul Mayer,

View willhime's profile


167 posts in 2419 days

#5 posted 09-06-2016 07:44 PM

Running through a planer isn’t an option since the general size I make is at least 16”-18” wide, but I probably wouldn’t anyways since I imagine the blades wouldn’t last past 2 boards even with sacrificial pieces glued around the edges. I could stand to get better at glue ups, but I’m pretty satisfied with them thus far. I always start with 60 grit, then 120, then 220. On this board I got frustrated and went down to a 40 grit to help along the lines faster.
I’m considering building a drum sander now, given that I actually muster enough confidence to see it through. Other than that I’m kind of at a loss of how to approach the problem. I have a 1/2” whiteside bowl bit, but the contact surface from that bit if I want to take just a 1/32 or 1/64” off is about 1/4” at most.

-- Burn your fire for no witness

View JKN's profile


10 posts in 1576 days

#6 posted 09-06-2016 09:11 PM

I start with 80 Grit on my belt sander then 100, 120, 150 on random orbit sander then hand sand 150 and 220 then butcher block finish


View Steve Peterson's profile

Steve Peterson

419 posts in 3962 days

#7 posted 09-06-2016 10:18 PM

I like Paul’s suggestion about using a handheld belt sander. It will be doing almost the same thing that a drum sander can do, except you are controlling how flat it ends up. You might want to add a perimeter of cheap sacrificial material to keep from rounding off the corners. Switch to a ROS at around 120 grit after it is flat.

-- Steve

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics