All Replies on Baby Crib...Topcoat for Shellac?

  • Advertise with us
View PhilipTheGasTank's profile

Baby Crib...Topcoat for Shellac?

by PhilipTheGasTank
posted 08-30-2016 04:40 PM

6 replies so far

View Bill White's profile

Bill White

5303 posts in 4814 days

#1 posted 08-30-2016 04:48 PM

I would doubt that the little one is trained to pee on vertical surfaces. :)
Stick with the shellac, and refresh it as might be needed. You will be surprised as to the integrity of the finish.
Just my thoughts.
Kryptonite can be bought under the brand name MinWax. It is good for repelling, but not good for much else.
Wanna know how I REALLY feel?

-- [email protected]

View bbasiaga's profile


1243 posts in 2849 days

#2 posted 08-30-2016 04:48 PM

GF High Performance Topcoat will provide more protection and goes on perfectly clear. I know it dries in like 2 hours, but not sure how long before it cures.

Shellac doesn’t cure. It just dries.


-- Part of engineering is to know when to put your calculator down and pick up your tools.

View nightguy's profile


213 posts in 1516 days

#3 posted 08-30-2016 05:23 PM

One trick for curing according to Bob Flexner, it you cant smell it it is cured. For most oil based Poly that is about 2-3 days, depending on temp.

View Fred Hargis's profile

Fred Hargis

6428 posts in 3347 days

#4 posted 08-30-2016 05:53 PM

My first choice would be a quality oil based varnish, like P&L 38 (hard to find) or SW Fast Dry Oil Varnish. Neither are a urethane formula, but rather an alkyd formula and look really nice; the SW product is a lot more amber than the P&L. But they do have the complication of being very slow to fully cure, and if quickness is important my next choice would be a good quality waterborne. At the top would be GF EnduroVar, followed by other GF products like HP, or maybe something from Target Coatings EM 6000, or maybe EM 8000. The Target Coating products can be catalyzed to make them even more durable.

-- Our village hasn't lost it's idiot, he was elected to congress.

View PhilipTheGasTank's profile


2 posts in 1489 days

#5 posted 08-31-2016 10:40 AM

Hey Thanks for all the qwick replies.

Think i may go with just the shellac for now… i like the fact that i dont need to wait for it to cure and there is no guessing if hes sleeping in something toxic. Plus i really like the finish so far

After my son out grows the crib i believe i will add that extra layer of protection. If any concerns with applying future applications a year or 2 from now that would be helpful tho. I think i may apply one of freds suggested oil varnishes.

View Jake's profile


850 posts in 2485 days

#6 posted 08-31-2016 11:49 AM

I don’t personally see any need to put on anything except shellac. The crib you can see in my projects was finished with only shellac, been in use for almost a year and a half now, no problems yet. One spot under the sippy cup got some water damage after my daughter splashed water around and my wife let the cup sit in the puddle

But I don’t see any problems since shellac is so easy to sand and refinish, even just the trouble spot.

At the current rate, re finishing a 2×2” every couple of years seems like a non-issue, especially since I never have to wonder if the finish I am using is actually food safe – in shellac’s case I know for a fact that it is

-- Measure twice, cut once, cut again for good measure.

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics