LumberJocks

All Replies on Dovetail Jig Help

  • Advertise with us
View swpowe's profile

Dovetail Jig Help

by swpowe
posted 08-29-2016 01:11 PM


9 replies so far

View Kirk650's profile

Kirk650

598 posts in 1044 days


#1 posted 08-29-2016 01:58 PM

I’ve got the PC jig, but have only done through dovetails. That said, looks to me like you aren’t cutting to the right depth. Set the router bit cut depth to the thickness of the wood.

View BurlyBob's profile

BurlyBob

6086 posts in 2561 days


#2 posted 08-29-2016 04:02 PM

I tried the same thing with pine on my Leigh jig. My advice…toss the pine and use poplar. I did and it made all the difference in the world.

Finding the sweet spot with the dovetail bit, I found can be a real pain. Looks to me like you need to raise the bit or have less bit protruding a past the base. That description in and of itself can be confusing to say the least. I struggled for over a month from my first dovetail joint to getting to half blind rabbeted dovetails. Keep after it the results are worth it.

View Bill White's profile

Bill White

5180 posts in 4256 days


#3 posted 08-29-2016 04:10 PM

View HokieKen's profile

HokieKen

8559 posts in 1434 days


#4 posted 08-29-2016 04:19 PM

Your cut depth should be about 1/16” deeper than your dovetail diameter. So for 1/2” dovetails, set your cut depth to 9/16”. That should get you pretty close but like Bob said, you’ll still have to fiddle and tweak to get it just right.

-- Kenny, SW VA, Go Hokies!!!

View jwmalone's profile

jwmalone

769 posts in 998 days


#5 posted 08-29-2016 05:00 PM

I had the same problem, I tossed the jig and got a dovetail saw.

-- "Boy you could get more work done it you quit flapping your pie hole" Grandpa

View pintodeluxe's profile

pintodeluxe

5881 posts in 3109 days


#6 posted 08-29-2016 05:37 PM

If the sockets aren’t deep enough, adjust the knobs that control the template position. The template needs to move away from the operator to make a deeper cut. There are adjustment lines on the jig to get you close, then just make a couple test cuts until the tails fit flush in the sockets.

Another common problem is not having the bit depth set correctly. That controls how snugly the tails fit into the sockets. If the fit is too tight, adjust the bit depth to make a more shallow cut.

See page 18 here…
http://go.rockler.com/tech/RTD10000210AA.pdf

I have and use several dovetail jigs including Leigh, Akeda, and Porter cable. I still find the 4210 / 4212 to be a solid jig and a good value.

-- Willie, Washington "If You Choose Not To Decide, You Still Have Made a Choice" - Rush

View tmasondarnell's profile

tmasondarnell

105 posts in 2085 days


#7 posted 08-29-2016 08:55 PM

I was having a bunch of similar problems when I first got mine.

I found this video to be very helpful:

https://www.youtube.com/watch?v=RzgnOvu9afU

I highly recommend getting what the video calls a small scale (basically s 3-4 inch ruler with a sliding reference point). It is useful not only to center the top board, but also to set the distance of the template (that pintodeluxe mentions). I found I was setting the template on an angle which was throwing me off.

Also, make sure the boards are not shifting

View Woodmaster1's profile

Woodmaster1

1130 posts in 2882 days


#8 posted 08-29-2016 10:10 PM

I have two routers dedicated to making dovetails. Once I get them dialed they are ready to go when needed. I have the Leigh super jig. I don’t use the bushing that came with it, I find it harder to setup. A 7/16 brass bushing is what I use.

View bbasiaga's profile

bbasiaga

1243 posts in 2290 days


#9 posted 08-29-2016 10:51 PM

I have this jig as well. I think the above posts are right that the template itself is too far forward (close to you). Once you get that pushed back enough that the half blind side is as deep as the dovetail sides, you may have to tweak the depth of the bit to make them looser or tighter. Once its set, you just batch them out. Set up usually takes me longer than the actual drawers, but I don’t use the jig often and am always backing up on the learning curve a bit.

Brian

-- Part of engineering is to know when to put your calculator down and pick up your tools.

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com