LumberJocks

All Replies on Which first bandsaw? 10" or 14"

  • Advertise with us
View bryan11's profile

Which first bandsaw? 10" or 14"

by bryan11
posted 08-07-2016 04:16 PM


19 replies so far

View Fred Hargis's profile

Fred Hargis

5539 posts in 2880 days


#1 posted 08-07-2016 04:24 PM

I’d go with the 14” from the getgo. It’s about the best balance between the large and small saws (my opinion).

-- Our village hasn't lost it's idiot, he was elected to congress.

View knotscott's profile

knotscott

8289 posts in 3762 days


#2 posted 08-07-2016 04:30 PM

10” will limit you a lot in comparison to a 14”. The 14” seems to be the sweet spot for value and function for a hobbyist. Blade choice and setup are important factors.

-- Happiness is like wetting your pants...everyone can see it, but only you can feel the warmth....

View SenecaWoodArt's profile

SenecaWoodArt

445 posts in 2006 days


#3 posted 08-07-2016 04:39 PM

My basic rule of thumb for woodworking is buy the best you can afford. Buy right and cry once. Why would you buy something that you know that you will have to replace?

-- Bob

View DirtyMike's profile

DirtyMike

637 posts in 1288 days


#4 posted 08-07-2016 05:01 PM

Dont even bother with the 10 , you will want the 14 if you buy a 10. now if it were a 10’’ vs 12’’ table saw conundrum….

View Loren's profile

Loren

10477 posts in 4034 days


#5 posted 08-07-2016 05:31 PM

The only 10” saw I would recommend is the INCA340.

Great little saw with a nice motor.

Compared to that saw most of the 10” saws are pretty
chintzy. The standard for 14” saws is better and
there are a lot of aftermarket doo-dads you can get
to make a 14” saw cut more like a 20” industrial saw.

View bondogaposis's profile

bondogaposis

5398 posts in 2738 days


#6 posted 08-07-2016 06:12 PM

A 14” saw is a much better choice, for 2 reasons. A larger saw equals longer blade and longer blades run cooler and a larger diameter wheel is also easier on the blade. Longer blade life and better cuts.

-- Bondo Gaposis

View MikesProjects's profile

MikesProjects

172 posts in 2288 days


#7 posted 08-07-2016 06:22 PM

10” are toys. The 14” kicks butt. My brother loves his harbor freight 14” bandsaw with it 4 speed ability. I use TWO Delta 14” bandsaws. They are good quality. I bought them used several years apart for $140 each scanning CL, they were jump up right now & go kind of deals though. I have a 10” that was given to me, it sits in the rafters collecting dust. I suggest you put the money towards a 14” if you want to enjoy using a bandsaw, try to get a 1hp, happy wood working!

-- -Mike, Southern California, YouTube User ( Give & Take )

View bryan11's profile

bryan11

15 posts in 1066 days


#8 posted 08-07-2016 07:22 PM

Thanks for great recommendations. I’ll skip the 10” and go directly to 14”. We have a Harbor Freight in town, so their 14” bandsaw would be $314 with tax using a 20% coupon. The Grizzly G0555LX would be $634 with freight, so I’ll have to figure out whether the Grizzly is worth the extra $320 in cost.

View MrRon's profile

MrRon

5479 posts in 3630 days


#9 posted 08-07-2016 08:14 PM

Go to the HF web site and read the reviews for the 14” BS. After you read them, I don’t think you will want to buy a HF.

View SenecaWoodArt's profile

SenecaWoodArt

445 posts in 2006 days


#10 posted 08-08-2016 04:03 AM

Grizzly is worth every penny it will cost you over HF.

-- Bob

View mike02130's profile

mike02130

170 posts in 1059 days


#11 posted 08-08-2016 11:04 AM

Go with a nice used Delta 14”. It’s pretty much the standard. I just picked one up off of Craigslist with a 3/4 hp motor and twenty blades for $300. That was a good deal. In my parts they average in the 4 to 500 range. Plus it’s American made.

-- Google first, search forums second, ask questions later.

View OSU55's profile

OSU55

2299 posts in 2376 days


#12 posted 08-08-2016 11:36 AM

Depends on how you plan to use the bandsaw. If you have access to thick rough lumber and you’re going to resaw for dimensional lumber, cut your own veneer, and/or rip your lumber with it instead of a TS, then bigger is better, and you might as well go 17” vs a 14” and riser block.

For most everything else, my 10” Craftsman has handled everything I’ve needed. Far from a toy, it cuts right through 1” & 2” lumber, cuts curves, bevels, circles, etc. It will resaw, but only up to 4-1/2”. Same as with bigger saws, it just needs the right blade for the job. It will stay in my shop if I do get a bigger saw for resawing.

If you can find a good used bigger saw for the right price, that’s the way to go. If not, don’t shy away from buying a 10”. Not all 10” are created equal. The Craftsman and Rikon appear to be the same, and are superior to the other brands I looked at.

View RandyinFlorida's profile

RandyinFlorida

257 posts in 2454 days


#13 posted 08-08-2016 11:44 AM

I have the Grizzly LX, my only recommendation is to add the riser block.

-- Randy in Crestview Florida, Wood Rocks!

View Woodbum's profile

Woodbum

874 posts in 3452 days


#14 posted 08-08-2016 11:51 AM

Get the 14”. IMHO this will last you a lot farther down the road than the 10”. I know, I started with a 10” and immediately wanted something with more capacity. I would like a newer, bigger saw, but my 14” Jet is still going strong after 18 years with some added Carter modifications. IF I did get a new saw, it would be a Grizzly. More value with great features and power. Have fun, work safely and good luck!

-- "Now I'm just another old guy wearing funny clothes"

View bryan11's profile

bryan11

15 posts in 1066 days


#15 posted 08-08-2016 11:18 PM

Thanks again for all the help. I’ll watch CL for a while to see if I can find an old 14” Delta or similar, and if nothing shows up for too long I’ll order the Grizzly LX.

View Rentvent's profile

Rentvent

151 posts in 1235 days


#16 posted 08-09-2016 12:01 AM

This Craftsman 14-in bandsaw was on sale for $338 a couple weeks ago. I suspect that it will probably go that low again on Black Friday. At the current price of $420 it is still a decent deal and worth every penny over the HF saw.

Another option is to “rent” a ~$80 10” bandsaw from CL while you wait on a deal on a 14”. Once you snag your deal, you can sell the renter 10” for ~$50.

View KelleyCrafts's profile

KelleyCrafts

3713 posts in 1126 days


#17 posted 08-09-2016 03:55 PM

I bought the Grizzly G0555P for $499 delivered to me door. Sure it’s not the LX but I spent the extra $130 the LX would have cost on the riser block and a Timberwolf blade. I couldn’t be happier. The LX doesn’t have that many additional features worth the money and now I can resaw rough lumber up to 12” tall.

Just a thought.

-- Dave - http://kelleycrafts.com/ - pen blanks - knife scales - turning tools

View Matt's profile

Matt

160 posts in 1338 days


#18 posted 08-11-2016 06:24 PM

I’ve got a Jet 16” that I got in a package deal off CL with a Delta Floor Drill Press. I added Carter guides, replaced the worn out tires with Carter urethane tires and use Laguna blades and am very happy with it. I do wish it was a little bit lighter, it was a bear to get it in my basement. Overall for about a $500 investment (including Carter upgrades.) it was totally worth it. Also the floor space between the 16” and 14” isn’t much different.

-- My "projects" always look better with beer goggles.

View hackery's profile

hackery

49 posts in 1098 days


#19 posted 08-11-2016 08:20 PM

Just to throw my hat into the ring…. definitely as big as you can afford / fit in your work space. I deeply regret buying a 8” saw primarily because when I started woodworking (last summer) I wasn’t sure I would have a use for one often (I was wrong I use it all the time), I couldn’t afford a better one as the next size up being a 10” was over $300 more expensive than the $150 I already spent (power tools are a fortune in the UK) and I have a very small 12ft x 10ft shop. So please learn from this novice’s mistakes and buy as big as you can or you will regret it like me. I have been trying to kill my crappy saw as wife won’t let me buy another whilst it’s still working!

Be sure to get some quality blades for the saw as crappy as my small saw is it was the difference between night and day once I bought decent blades the included one was as helpful as a dose of the clap.

-- Notice woodworker and now metal worker - Belfast, Northern Ireland, UK

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com