LumberJocks

All Replies on VeritasĀ® Skew Block Plane

  • Advertise with us
View KelleyCrafts's profile

VeritasĀ® Skew Block Plane

by KelleyCrafts
posted 08-04-2016 05:55 PM


9 replies so far

View Loren's profile

Loren

10477 posts in 4041 days


#1 posted 08-04-2016 06:04 PM

I’ve had some skew planes.

My opinion is it’s preferable to have the pointy
corner of the iron in the shoulder of the rabbet,
so perhaps if you’re right handed you might
prefer to push the plane one way rather than
the other.

I have an old Japan skew rabbet plane that’s
pretty adequate. It has a fence and it was
cheap on ebay. I don’t use it much but since
I sold the other skew planes I keep it around.

View KelleyCrafts's profile

KelleyCrafts

3716 posts in 1132 days


#2 posted 08-04-2016 06:06 PM

Yeah, I figured I would get one that point toward the wood (away from the fence when pushed right handed). Was just curious if two are really necessary. I just can’t see the expense and the history of things adding up.

-- Dave - http://kelleycrafts.com/ - pen blanks - knife scales - turning tools

View Homick's profile

Homick

23 posts in 2314 days


#3 posted 08-10-2016 04:44 PM

If you only have one version, you can only plane in one direction. The plane design prevents ‘swapping sides’. Eventually, you will have to plane against the grain if you only have one version; bad things happen when you do this.

if you want to avoid skew rabbet planes altogether, scribe a line on your shoulder, cut down to your rabbet depth with a saw and remove the remainder of the rabbet material with a shoulder plane or a chisel.

View WhoMe's profile

WhoMe

1564 posts in 3636 days


#4 posted 08-10-2016 05:05 PM



If you only have one version, you can only plane in one direction. The plane design prevents swapping sides . Eventually, you will have to plane against the grain if you only have one version; bad things happen when you do

- Homick

Another possibility might be project specific in that there may not be room for one version or the other on that specific project.

In my case it would most likely be because I’m left handed and I do a lot of things opposite of the right handed norm.

-- I'm not clumsy.. It's just the floor hates me, the tables and chairs are bullies, the wall gets in the way AAANNNDDD table saws BITE my fingers!!!.. - Mike -

View KelleyCrafts's profile

KelleyCrafts

3716 posts in 1132 days


#5 posted 08-10-2016 06:14 PM

Well, I guess we will see soon enough. I have one coming next Tuesday. I’m cheap so I opted for ground shipping. Apparently it’s by bicycle.

I do have a Stanley 220 I use. It’s not awesome but it isn’t too bad. So that with a right handed skew will hopefully be adequate. I actually have a hand full of block planes but only really like the 220 enough to use right now.

-- Dave - http://kelleycrafts.com/ - pen blanks - knife scales - turning tools

View Don W's profile

Don W

19212 posts in 2960 days


#6 posted 08-11-2016 12:49 AM

I’vegot the pair. I like a lot.

-- http://timetestedtools.net - Collecting is an investment in the past, and the future.

View KelleyCrafts's profile

KelleyCrafts

3716 posts in 1132 days


#7 posted 08-11-2016 01:41 AM

I have no doubt Don I will love the plane. Mainly worried about if I really need the pair instead of just one. I ordered the right handed version. If I find that a scraper doesn’t help clean up wrong grain direction then I’ll order the left handed one I suppose.

-- Dave - http://kelleycrafts.com/ - pen blanks - knife scales - turning tools

View TheFridge's profile

TheFridge

10858 posts in 1879 days


#8 posted 08-11-2016 02:41 AM

I have the right handed. Haven’t found a need for the left as almost all rabbets will be on the inside of the joinery.

-- Shooting down the walls of heartache. Bang bang. I am. The warrior.

View KelleyCrafts's profile

KelleyCrafts

3716 posts in 1132 days


#9 posted 08-11-2016 03:04 PM

Thanks Fridge. I read your review but you aren’t one for long stories so…. :)

This will be my first new hand plane other than the Veritas router. Kind of excited to try a new one but hope I don’t start looking at my old Stanley’s different.

-- Dave - http://kelleycrafts.com/ - pen blanks - knife scales - turning tools

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com