LumberJocks

All Replies on New to shapers and can't get it adjusted

  • Advertise with us
View Brian's profile

New to shapers and can't get it adjusted

by Brian
posted 12-20-2018 05:33 AM


6 replies so far

View Brian's profile

Brian

185 posts in 2389 days


#1 posted 12-20-2018 06:20 AM

I left out the part where i purchased it used. I just joined and planed some 1” thick 30 year old white oak and made new fences for it and replaced the plastic that was previously on it. I may have solved my problems somewhat.

-- “Always take a banana to a party, bananas are good!” - Tenth Doctor

View TungOil's profile

TungOil

1201 posts in 853 days


#2 posted 12-20-2018 07:04 PM

Can you post some photos of the issue? From your description I would agree it is probably the fences. One trick to get your fences truely co-planer is the make them thick and mount them to the guard making sure the mounting hardware is well countersunk below the face (very important!). Then run the assembly across the jointer a few times to true everything up. That will solve 99% of any sniping problems you are having.

-- The optimist says "the glass is half full". The pessimist says "the glass is half empty". The engineer says "the glass is twice as big as it needs to be"

View AlaskaGuy's profile

AlaskaGuy

5233 posts in 2667 days


#3 posted 12-20-2018 07:28 PM


Can you post some photos of the issue? From your description I would agree it is probably the fences. One trick to get your fences truely co-planer is the make them thick and mount them to the guard making sure the mounting hardware is well countersunk below the face (very important!). Then run the assembly across the jointer a few times to true everything up. That will solve 99% of any sniping problems you are having.

- TungOil

+1 pictures and better description of problem. I saw your post last but didn’t know what “I’m not getting an even cut down the entire stile’ means.

-- Alaskan's for Global warming!

View AlaskaGuy's profile

AlaskaGuy

5233 posts in 2667 days


#4 posted 12-20-2018 08:24 PM

BTW I’d recommend this book.

https://www.amazon.com/Shaper-Handbook-Roger-W-Cliffe/dp/0941936694/ref=sr_1_2?s=books&ie=UTF8&qid=1545337098&sr=1-2&keywords=The+shaper+book

There are at least 4 different way to set up for the sticking cut on a shaper(that I know of)’

Fences co-planer
Off set fence
outboard or back fence
one piece fence
Each have there advantages and disadvantages

-- Alaskan's for Global warming!

View AlaskaGuy's profile

AlaskaGuy

5233 posts in 2667 days


#5 posted 12-21-2018 09:56 PM

So Brian, how’s your problem doing. Did you bail on us?

-- Alaskan's for Global warming!

View Jared_S's profile

Jared_S

172 posts in 317 days


#6 posted 12-22-2018 01:06 AM

If you cutting the entire edge use a outboard / back fence and just use the split fence for dust collection…(only with a feeder)

https://youtu.be/nEGDxhD1RO8

If you are not taking a full face profile cut (you should to reduce tearout) I would use a continuous fence.

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com