LumberJocks

All Replies on Using a tablesaw with a generator

  • Advertise with us
View Anselm's profile

Using a tablesaw with a generator

by Anselm
posted 12-08-2018 11:16 PM


5 replies so far

View Richard Lee's profile

Richard Lee

260 posts in 1387 days


#1 posted 12-09-2018 12:35 AM

Sure , why not.
Make sure its sized accordingly for startup amp draw.

View MikeDilday's profile

MikeDilday

284 posts in 1071 days


#2 posted 12-09-2018 03:53 AM

Can you handle 220 volts? The amperage draw would be a lot less.

-- Michael Dilday, Suffolk, Va.

View WoodenDreams's profile

WoodenDreams

894 posts in 523 days


#3 posted 12-09-2018 05:02 AM

The Grizzly Hybred G0177Z can be wired for 20amp 120v, or 15amp 240v. The Grizzly Hybred G0833P can be wired for 16amp 110v, or 8amp 230v. What model do you have. What does the manual say. If you call the Grizzly 1-800-523-4777 and ask the salesman for a service rep, they’ll switch you over. They can give you answers.

View Manitario's profile

Manitario

2798 posts in 3495 days


#4 posted 12-09-2018 05:08 AM

You can run anything from a big enough generator but good luck finding a cheap generator that will handle 30 amps!

-- Sometimes the creative process requires foul language. -- Charles Neil

View CaptainKlutz's profile

CaptainKlutz

2285 posts in 2106 days


#5 posted 12-09-2018 06:06 AM

Tough predicament: Generator big enough to run a 20A (30A peak) 120V saw will be almost as much as cost quoted by electrician.

Couple of suggestions:
1) Change saw over to 240V.
Just about any solution to get more power in shop will be easier with 20A 240V circuit, then a 30A 120V circuit; regardless of whether using a generator, or adding new 240V outlet in shop. 30A circuit requires 10 AWG wire and that stuff is significantly more expensive than 12 AWG required for 20A. 30A plugs/receptacles are also 1.5X more.

2) After you convert the saw to 240V, make a 12/3 extension cord with dryer plug on end and run cord inside to laundry room (which is usually next to garage). Wife can live without dryer when you need saw. 12/3 SO rubber cord is less then $1 foot, you can easily tolerate 100ft cord length to dryer plug from your 240V saw if needed (even 150ft of 12/3 should not drop voltage enough to effect saw). A long saw extension cord may sound expensive @ $1 ft, but its cheaper than electrician or generator. :)

2) Get some more quotes on increasing power to shop. $1800 for one 30A circuit is a rip off (unless the run length is over 400+ feet?). For <$1800, you typically get an entire 60-100A sub-panel installed with bunch of circuits for your workshop (including electrical wiring permits with city/county).
I would ask for quotes on single 20A 240V circuit run to shop, and 60A sub-panel with (1) 20A 240V and (2) 20A 120V outlets; so you can see cost difference. Be sure to ask for cost breakdown. wink wink,

Best Luck.

-- I'm an engineer not a woodworker, but I can randomly find useful tools and furniture inside a pile of lumber!

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com