LumberJocks

All Replies on Sliding Compound Miter

  • Advertise with us
View NCJOB's profile

Sliding Compound Miter

by NCJOB
posted 12-04-2018 03:35 PM


8 replies so far

View Joeswoodshop's profile

Joeswoodshop

5 posts in 321 days


#1 posted 12-04-2018 04:03 PM

I am not a fan of a lot of HF power tools. However if you are going to go that route I would pick up that Hercules 12” saw. Looks like a Dewalt copy and has good reviews. Also question why you want a 12” slider if your making crafts,small stuff? I have a 10” and a 12” and the 10” can cut 80% of what I need a miter saw to cut. If you go the cheap cheap route your probably going to regret it. The best advice I always give is to buy the best, even if you have to save a little longer. That way you only pay once! Good luck.

View jimintx's profile

jimintx

921 posts in 2094 days


#2 posted 12-04-2018 04:16 PM

When you write that you aren’t able to spend 250-400, does that mean you have an upper limit of something a bit south if $250? The Hercules 12” saw is only $50 under 400, if zi am looking at the same one Joe has in mind.

Just for conversation:
If it is for small stuff, then 10” is probably good, and sliding feature likely isn’t needed. Sliding components add flexibility, and fitment play in the system, and can thus be the source of imprecise cuts. That might exacerbated by going cheap.

Also, do you want the compound miter feature?

I suggest a great way to look at some options is to shop carefully for miter saws on the Home Depot web pages.

.

-- Jim, Houston, TX

View Robert's profile

Robert

3537 posts in 1990 days


#3 posted 12-04-2018 04:19 PM

First, you don’t really need a slider if that’s what your doing. A 12” miter saw will cut a 7-8” wide board.

Second, if you buy HF you’re gonna get what you pay for. Personally, I wouldn’t waste my money.

Used is the way to go IMO. You should be able to pick up a non slider for <$200. For example, 30 second search: here's the exact model I have for 100 bucks.

All that said, a sharp, tuned up hand saw cuts quite well.

-- Everything is a prototype thats why its one of a kind!!

View RobHannon's profile

RobHannon

317 posts in 1040 days


#4 posted 12-04-2018 04:26 PM

The cheaper HF slider probably will be fine if it is not going to be used on sites, i.e. thrown in and out of the back of a truck. Not gonna be anything to write home about but if you spend some time on it you should be able to get 90 degree cuts on it reliably.

If you are patient, used is the way to go. Keep an eye out for construction/remodeling folks who want to switch over to some of the battery powered mitersaws that are gaining popularity.

View ChefHDAN's profile

ChefHDAN

1459 posts in 3359 days


#5 posted 12-04-2018 04:50 PM

If you do not have a table saw yet and you’re interested in doing woodworking, I really think you’re better off getting a used TS and build a crosscut sled. You’ll have much more precise cuts and overall versatility. I’ve got a compound miter saw that I mostly use for rough work, and would not buy a slider, (certainly not a HF one), because of the footprint it needs in the shop and the poor accuracy of it’s cuts…. I do occasionally dream of knocking over a bank and buying a Kapex though :-)

-- I've decided 1 mistake is really 2 opportunities to learn.. learn how to fix it... and learn how to not repeat it

View waho6o9's profile

waho6o9

8770 posts in 3087 days


#6 posted 12-04-2018 04:53 PM

https://charlotte.craigslist.org/search/sss?query=miter%20saws&sort=rel

https://raleigh.craigslist.org/search/sss?query=miter%20saw&sort=rel

https://hickory.craigslist.org/search/sss?query=miter%20saw&sort=rel

Might I suggest Craigslist as there’s a plethora of good saws that will cut down on your frustrations
when you use the lower end saws. Keep in mind 12” saw blades are not cheap.

Best of luck.

View NCJOB's profile

NCJOB

7 posts in 326 days


#7 posted 12-04-2018 06:31 PM

Thanks everyone for the advise. It has been really helpful and I think I am going to hold off on the HF saw.

I do have a TS and I think the sled is my best bet for the moment. Sled would also give me a great project to work on.

Jeff

-- Jeff, NC

View SMP's profile

SMP

1392 posts in 415 days


#8 posted 12-04-2018 07:23 PM



Thanks everyone for the advise. It has been really helpful and I think I am going to hold off on the HF saw.

I do have a TS and I think the sled is my best bet for the moment. Sled would also give me a great project to work on.

Jeff

- NCJOB

Actually a lot of jigs make really good projects that can be used on the table saw. They don’t take expensive wood. Most you don’t have to get exact. And they are really useful and will help your woodworking as you progress. Several books on just jigs to make. I have a 12” dewalt sliding compound miter saw but I use it mainly for construction type of stuff, flooring, decking, crown molding, etc. The only time I use it for “woodworking” is when I just need to chop a piece or 2 to length, and don’t want to get my table saw out(its on wheels and I cut outside- no dust system).

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com