LumberJocks

All Replies on Drill Press drum sander

  • Advertise with us
View Oldschoolguy's profile

Drill Press drum sander

by Oldschoolguy
posted 11-25-2018 06:45 PM


13 replies so far

View mel52's profile

mel52

729 posts in 564 days


#1 posted 11-25-2018 08:31 PM

I had one when I first started. If you can make a little box type table with an interchangeable piece with a hole sized just a smidgeon larger than each drum you will be using you can hook up shop vac or whatever to the back or side and you won’t have much of a dust problem. Have a friend that just puts a cheap box fan up close to the sander with a furnace filter to suck dust away. I have a Wen osc. spindle sander that works well, but I was thinking that Harbor Freight might have one cheaper. Not as expert on this but it worked for me.

-- MEL, Kansas

View Planeman40's profile

Planeman40

1365 posts in 3061 days


#2 posted 11-25-2018 09:10 PM

Been using one of these successfully for the past 60 years or so. Like mel52 above says, just make a recess hole in the table for the end of the sander to drop into. It helps a lot to have a spindle lock on the drill press to lock the height of the spindle in various vertical positions so you can use other parts of the sanding tube after the used area gives out.

-- Always remember: It is a mathematical certainty that half the people in this country are below average in intelligence!

View WoodenDreams's profile

WoodenDreams

505 posts in 211 days


#3 posted 11-25-2018 10:04 PM

The spindle sanding bit for the drill press is not that expensive. Your drill press table probably has a slot to remove, for drilling through holes. just remove that slot for the sanding bit to fit down in, allowing full use of the spindle sanding bit. The drill press is designed to go up & down, so this would put a side pressure on the press, possibly shortening the life of the bearings on the press. Occasional use like this should be alright. Purchasing a oscillating spindle sander for around $150 is the better way.

View Jim Finn's profile

Jim Finn

2691 posts in 3222 days


#4 posted 11-25-2018 11:07 PM

I use a pneumatic sanding drum on my drill press with great results. The hard ones , not so much.

-- No PHD just a DD214

View BurlyBob's profile

BurlyBob

6090 posts in 2565 days


#5 posted 11-26-2018 06:47 AM

This past summer I bought a Wen oscillating spindle sander from Walmart for under $100. It pretty much fills my needs. It doesn’t take up much space either. The only negative is that it’s a tad noisy. It might be an option for you.

View HokieKen's profile

HokieKen

8689 posts in 1438 days


#6 posted 11-26-2018 03:45 PM

I’m with BurlyBob. I’ve been very happy with the Wen OSS.

Prior to picking up the OSS, I used sanding drums in my drill press successfully. Long-term it could cause bearing failure as WoodenDreams points out above. Also, if you put too much pressure on the drum, it can loosen the taper fit of the shaft in the spindle and cause your chuck to fall out.

-- Kenny, SW VA, Go Hokies!!!

View splintergroup's profile

splintergroup

2573 posts in 1522 days


#7 posted 11-26-2018 04:40 PM

I have (and use) them. but they are not the greatest. A dedicated spindle sander would be much better.
Of course the drill press drums are inexpensive and well worth a try, just don’t expect miracles 8^)

View ChefHDAN's profile

ChefHDAN

1330 posts in 3149 days


#8 posted 11-26-2018 09:01 PM

Used one before getting my Clayton OSS, did a good job at least until I found out how much better the OSS is, but $100 is $100 and unless you see the need in the future the $20 kit at Lowe’s can do what you need for now, be sure to remember to let the sand paper do the work, don’t put alot of pressure against the quill.

-- I've decided 1 mistake is really 2 opportunities to learn.. learn how to fix it... and learn how to not repeat it

View bilyo's profile

bilyo

565 posts in 1402 days


#9 posted 11-27-2018 04:03 PM

As mentioned above, a sanding drum on a drill press does work and is an economical approach. Also, as suggested above, because the drum on a drill press does not oscillate, it takes more side pressure to get the job done. Just keep this in mind and don’t force it. Also, as mentioned, it will create lots of very fine dust. Just work out some way to collect it and wear a dust mask.

View MrRon's profile

MrRon

5364 posts in 3543 days


#10 posted 11-27-2018 10:32 PM

I have always been opposed to using a tool in a way which it wasn’t designed for. A drill press is designed to drill holes with the loads applied vertically. The bearings for a DP are not designed for side loads and will eventually fail.

I have used the DP for sanding, but very sparingly. I bought a Wen OSS for $100 and it does what I need it for.

View WoodenDreams's profile

WoodenDreams

505 posts in 211 days


#11 posted 11-28-2018 08:45 AM

Home Depot has a Wen spindle sander for $99. Might be your best choice to keep your cost down, and a sander designed for spindle sanding.

View eflanders's profile

eflanders

326 posts in 2150 days


#12 posted 11-28-2018 06:44 PM

I’m with Mr. Ron. Drill presses especially small bench top ones, will quickly lose their ability to drill a straight accurate hole when used as a a spindle sander.

View Andybb's profile

Andybb

1802 posts in 903 days


#13 posted 11-28-2018 07:03 PM



I have a Wen osc. spindle sander that works well, but I was thinking that Harbor Freight might have one cheaper.
- mel52

That WEN is a deal. The HF one is $144 – 20%.

-- Andy - Seattle USA

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com