All Replies on Never used a blade dampener before but interested. Can they be used on miter saws as well?

  • Advertise with us
View gauntlet21's profile

Never used a blade dampener before but interested. Can they be used on miter saws as well?

by gauntlet21
posted 11-15-2018 11:59 PM

7 replies so far

View AlaskaGuy's profile


5984 posts in 3157 days

#1 posted 11-16-2018 12:22 AM

If you want to get technical. Even though many woodworkers say “Chop saw” when they mean “Miter saw” its the wrong name.

I have some blade stabilizers. I never use them after I first tried them out. I can’t see where they help on a good saw blade.

Miter saw for wood and chop saw for metal. At least in my world.

-- Alaskan's for Global warming!

View pottz's profile


11215 posts in 1832 days

#2 posted 11-16-2018 12:39 AM

ditto to A G,i tried stiffeners years ago also and it seemed i was always putting them on and off and they never seemed to would never use on a mitre saw.

-- working with my hands is a joy,it gives me a sense of fulfillment,somthing so many seek and so few find.-SAM MALOOF.

View 000's profile


2859 posts in 1747 days

#3 posted 11-16-2018 12:43 AM

I never have used them on any of my wood chop saws.. :)

View gauntlet21's profile


69 posts in 1058 days

#4 posted 11-19-2018 05:02 PM

Thanks, I was just curious.


View EarlS's profile


3940 posts in 3196 days

#5 posted 11-19-2018 05:20 PM

For better or worse I have always had stiffeners on the table saw blade, but not on the miter saw. I do have a laser on the miter saw though which is really helpful.

The biggest issue with using a stiffener on the inside of the blade next to the arbor is the offset. I have different zero insert plates for saw blades and dado stacks since I take the stiffener off on the dado in order to get all of the blades on and still have room for the tightening nut.

Also, you can’t raise the blade up as high with a stiffener since it will hit the bottom of the insert plate.

Once again, it depends on what you are used to. I’ve always had this set up so it doesn’t bother me and it doesn’t take any longer when I’m changing blade set ups.

-- Earl "I'm a pessamist - generally that increases the chance that things will turn out better than expected"

View Planeman40's profile


1516 posts in 3609 days

#6 posted 11-20-2018 05:38 PM

For years I have never needed a stiffner on carbide tooth blades as the width of the carbide teeth means the steel blade body never rubs against the wood causing it to generate heat and warp. However in the “olden” days before carbide teeth (I’m a old codger) the teeth of the steel blade were offset slightly to each side to widen the kerf to solve the blade rubbing problem (hand saws too). But you still could get enough of the problem to warrant a blade stiffner to control the problem. A stiffner does limit the depth of the cut though.

-- Always remember: It is a mathematical certainty that half the people in this country are below average in intelligence!

View Bill White's profile

Bill White

5302 posts in 4808 days

#7 posted 11-20-2018 06:58 PM

Ya don’t need ‘em with a quality blade.

-- [email protected]

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics