LumberJocks

All Replies on Wood recommendation needed!

  • Advertise with us
View Karen's profile

Wood recommendation needed!

by Karen
posted 11-14-2018 06:16 PM


10 replies so far

View pintodeluxe's profile

pintodeluxe

6181 posts in 3624 days


#1 posted 11-14-2018 06:18 PM

Maple, poplar, oak, ash. The finish, as well as the lumber type, will affect the color. Shellac turns orange, lacquers turn yellow.

-- Willie, Washington "If You Choose Not To Decide, You Still Have Made a Choice" - Rush

View pottz's profile

pottz

10448 posts in 1795 days


#2 posted 11-14-2018 06:25 PM

ditto! my first choice would be maple.

-- working with my hands is a joy,it gives me a sense of fulfillment,somthing so many seek and so few find.-SAM MALOOF.

View Phil32's profile

Phil32

1084 posts in 714 days


#3 posted 11-14-2018 07:02 PM

I have had similar experience with shellac & lacquer – better results with water based polyacrylic. The wood suggested are the likely choices.

-- Phil Allin - There are mountain climbers and people who talk about climbing mountains. The climbers have "selfies" at the summit!

View a1Jim's profile

a1Jim

118104 posts in 4388 days


#4 posted 11-14-2018 07:21 PM

Is this for indoor or outdoor use?

-- https://www.artisticwoodstudio.com/videos

View bondogaposis's profile

bondogaposis

5807 posts in 3162 days


#5 posted 11-14-2018 08:00 PM

Quarter sawn sycamore is another consideration.

-- Bondo Gaposis

View PPK's profile

PPK

1770 posts in 1620 days


#6 posted 11-14-2018 08:47 PM

Gotta throw hickory (pecan) in there… It’s got color variation, but overall fairly light.

-- Pete

View CWWoodworking's profile (online now)

CWWoodworking

890 posts in 989 days


#7 posted 11-14-2018 09:40 PM

What is the project? Some woods are better suited for certain things.

I like poplar. I wouldn’t use it on a dining table unless it’s rustic.

I was picking up my lumber the other day and seen some really nice wood I didn’t recognize at first. Asked what it was, Hickory. Except it was from a particular part of the country (don’t remember where) and it didn’t have any streaks in it. Gorgeous light wood.

Someday when things slow a little, I may design something for that wood cause I thought that much of it.

View Andre's profile

Andre

3646 posts in 2616 days


#8 posted 11-14-2018 10:00 PM

I am partial to Birch,,, but then I did have a domestic supply a while back (A few planks left)! Tends to be a bit harder to finish than Maple? As far as Poplar, lovely wood to work with and finish, Shellac finish and maybe some clear wax.

-- Lifting one end of the plank.

View CaptainKlutz's profile

CaptainKlutz

3379 posts in 2305 days


#9 posted 11-14-2018 10:31 PM

Try the wood finder on the Wood Database site

+1 indoor/outdoor use makes a big difference.
Heavy UV exposure can change wood colors, and adds color to most top coats. Keeping an outdoor project in full sun ‘white’ and well protected from weather is near impossible, unless you paint it white.

+1 Intended purpose, or project is important also.
There are some ‘white’ woods like Holly, Aspen, Buckeye, or Cottonwood, that tend to be lighter than more common domestic species, like maple or ash; but they are not very strong. Would not use them for table top, but they are fine used in picture frame, some small hanging curio shelves, or turning projects.

+1 For indoor project, choice of finish has large impact on aging color changes for most ‘white’ woods. Finishes that change color the least are the water borne acrylic types, commonly called ‘water white’ finish. Many mfg produce these types of finishes, with GF polyacrylic most common at wood working stores. Note majority of the water borne acrylics are made to the sprayed, and not brush applied.

Best Luck.

-- If it wasn't for bad luck, I wouldn't have no luck at all, - Albert King - Born Under a Bad Sign released 1967

View Karen's profile

Karen

14 posts in 733 days


#10 posted 11-16-2018 02:32 PM

Thanks everyone! I appreciate your quick responses. Awesome suggestions, some of which I actually have on hand, too! Love it!

Btw, I neglected to say it’s for a router candy dish I designed. (Don’t judge or roll your eyes! I’m a novice, and this is all the talent I can muster right now!)

It’ll probably get light use—wrapped candy or maybe just displayed.

~Karen

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com