LumberJocks

All Replies on Best Hand Plane Type for Flushing Perp. Joints

  • Advertise with us
View CoreyCandlemaker's profile

Best Hand Plane Type for Flushing Perp. Joints

by CoreyCandlemaker
posted 11-06-2018 04:50 PM


11 replies so far

View Bill White's profile

Bill White

5225 posts in 4441 days


#1 posted 11-06-2018 05:09 PM

Very sharp iron, skew the angle of attack, and really fine shavings will accomplish the task. Don’t be ham-fisted in your approach.
I don’t have either of those planes, but the higher angle bedding doesn’t seem to be a plus unless the wood is highly figured.
Both of those planes will need some tweaking as do all planes. If you’re not skilled at that………well, now is as good a time as any to learn.
For me, I’d go with the Stanley unless you can get an older Stanley for a bargain.

-- [email protected]

View Andre's profile

Andre

2750 posts in 2287 days


#2 posted 11-06-2018 05:13 PM

DX or NX 60 from Lee Valley or for finer work a LN 102.

-- Lifting one end of the plank.

View HokieKen's profile

HokieKen

10750 posts in 1619 days


#3 posted 11-06-2018 06:28 PM

I agree with Andre in that I would go with a block plane. And I agree with Bill in skewing the angle of attack. So, my recommendation for this task (and a plethora of others) is a skewed block plane. If the Veritas is out of your budget range, vintage Stanley #140s can be had for less in the used market and are excellent users.

-- Kenny, SW VA, Go Hokies!!!

View Mr_Pink's profile

Mr_Pink

173 posts in 852 days


#4 posted 11-06-2018 07:25 PM


Very sharp iron, skew the angle of attack, and really fine shavings will accomplish the task.

I think this advice is more important than the type of plane. My personal preference would be to use a smoothing plane for this task simply because it would probably be in (or closer to) my hand already.

If you’re looking at smoothing planes that are priced close to a new Stanley no 4, I would consider Woodriver. I have their #3, and I think it was a great deal.

View OSU55's profile

OSU55

2385 posts in 2470 days


#5 posted 11-06-2018 09:08 PM



Very sharp iron, skew the angle of attack, and really fine shavings will accomplish the task. Don t be ham-fisted in your approach.

- Bill White


Agree with this. A 3 or 4 bench or about any decent block plane will work. I’ve used both to do the same job. Skew the blade to 45. No need for anything special.

View Max™'s profile

Max™

104 posts in 390 days


#6 posted 11-07-2018 03:56 PM

Am I the only one who grabs a card scraper if I can’t easily plane so the endgrain sides are supported by the facegrain piece?

I got a little japanese plane I like to use for that sort of quick joint cleanups where I can actually keep the sides supported, but otherwise I grab the scraper.

-- One hand to hold the saw, one hand to guide it, one hand to brace the work and in the sawdust OW MY THUMB!

View JohnMcClure's profile

JohnMcClure

691 posts in 1121 days


#7 posted 11-07-2018 04:11 PM

A bit off topic but your mention of table legs meeting aprons reminded me of something I read recently.
It is wise to offset the apron about 1/8” or so from the leg for exactly this reason: small misalignment – in construction or due to wood movement over time – is less noticeable if there is an obvious intentional offset.
I read this, looked at a coffee table base I’d built years ago (without this advice), and immediately saw its value.

The photo below is the recommended method, so that planing grain flush is not required:

Again, may not very useful to you, just wanted to share.

I do own the Stanley SW #4 and like it, but I’d be concerned about getting tearout in your case. Scraper may be best option.

-- I'd rather be a hammer than a nail

View SMP's profile

SMP

1336 posts in 386 days


#8 posted 11-07-2018 09:21 PM



Very sharp iron, skew the angle of attack, and really fine shavings will accomplish the task. Don t be ham-fisted in your approach.

I also agree with this. I have a 100+ year old Stanley #3. After watching some Paul Sellers videos I finally got it truly sharp and tuned and I am amazed at what it can do, and I don’t even really need to scrape or sand afterwards.

View TheFridge's profile

TheFridge

10859 posts in 1967 days


#9 posted 11-08-2018 01:45 AM

I’d Skew a block plane and roll into it the other grain. Super light cuts. Don’t want tearout. Will scraps it after to even it out.

Watch some doucette and Wolfe videos. One where casework is involved.

-- Shooting down the walls of heartache. Bang bang. I am. The warrior.

View BlasterStumps's profile

BlasterStumps

1390 posts in 920 days


#10 posted 11-08-2018 03:27 AM

My low angle Veritas jack will do the job well enough but the application of a little technique and finesse are required even though.

-- "I build for function first, looks second. Most times I never get around to looks." - Mike, western Colorado

View WoodenDreams's profile

WoodenDreams

707 posts in 392 days


#11 posted 11-08-2018 04:52 AM

a low angle block plane. and angle the plane for a angled slice instead of straight on. and would resharpen the blade before the work. or the time consuming way of sanding.

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com