LumberJocks

All Replies on Voltage conversion of an old Powermatic

  • Advertise with us
View Zonker's profile

Voltage conversion of an old Powermatic

by Zonker
posted 10-27-2018 01:57 PM


9 replies so far

View Planeman40's profile

Planeman40

1452 posts in 3267 days


#1 posted 10-27-2018 03:39 PM

Go ahead and upgrade the electrical panel for 220v single phase. If there is not enough space for an additional circuit in the existing panel, a new sub-panel can be added. I bet you are going to spend about the same amount of money trying to work around the problem. One last thing. Make sure the saw you are about to buy is 220v SINGLE PHASE and not three phase. Three phase presents a whole new set of problems. And yes, you can put a 10” blade on a 12” saw, but why would you want to if you went ahead and ran that 12” saw on 220v single phase. I have a 12” table saw and, believe me, that extra two inches is handy many times.

-- Always remember: It is a mathematical certainty that half the people in this country are below average in intelligence!

View Scap's profile

Scap

80 posts in 433 days


#2 posted 10-27-2018 03:46 PM

Option 1:
If the motor is dual voltage, rewire the motor for 110v.

Option 2:
If your panel has room for another two pole breaker, it should be easy to run a 220v circuit to the new saw.

Option 3:
If motor isn’t dual voltage, and you can’t get 220v pulled over to the saw, then you’ll have to consider buying a new motor, possibly a starter, and you will also be limited on how much horsepower you’ll be able to run.

View AHuxley's profile

AHuxley

874 posts in 3827 days


#3 posted 10-27-2018 10:19 PM

If you are considering a PM70 do yourself a favor and research it thoroughly it is the least loved Powermatic cabinet saw for good reason.

Both are likely to be 3ph so the motor won’t be dual voltage. Unless you find a used 120v motor and starter the money you save in the end will likely not make much sense.

View Zonker's profile

Zonker

98 posts in 357 days


#4 posted 10-28-2018 02:07 AM

Thanks everyone for the advice. I’ll let you know how things turn out.

-- Larry A. - I've made a small fortune with my woodworking. The trouble is, I started with a large fortune.

View Zonker's profile

Zonker

98 posts in 357 days


#5 posted 11-03-2018 01:47 AM

Update: It is a three phase motor, so that will have to be changed. The saw has seen some use but has real good bones. Someone painted it battleship gray but the inside still has that older Emerald green. The serial number is 166691, can anyone tell me about how old it might be?

-- Larry A. - I've made a small fortune with my woodworking. The trouble is, I started with a large fortune.

View MrUnix's profile

MrUnix

7478 posts in 2705 days


#6 posted 11-03-2018 03:31 AM

Serial number makes it a PM66 built in 1971. What motor is in it, and what is the FLA on it? If it’s the 1.5hp three phase model, you MAY be able to run it on 120v.

Cheers,
Brad

-- Brad in FL - In Dog I trust... everything else is questionable

View Zonker's profile

Zonker

98 posts in 357 days


#7 posted 11-03-2018 01:25 PM

It’s a 3 hp 3 phase Leeson. Currently trying to figure out whether I want a new motor or to go with a VFD. I need to learn more on VFD’s. I do not know what “FLA” means, can you enlighten me?

-- Larry A. - I've made a small fortune with my woodworking. The trouble is, I started with a large fortune.

View Scap's profile

Scap

80 posts in 433 days


#8 posted 11-03-2018 01:31 PM

Full Load Amps

View Zonker's profile

Zonker

98 posts in 357 days


#9 posted 11-03-2018 10:06 PM

Thanks everyone, I got outbid, maybe next time.

-- Larry A. - I've made a small fortune with my woodworking. The trouble is, I started with a large fortune.

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com