LumberJocks

All Replies on Is there a woodworking vise fit for my setup?

  • Advertise with us
View gauntlet21's profile

Is there a woodworking vise fit for my setup?

by gauntlet21
posted 10-14-2018 06:43 PM


11 replies so far

View TheFridge's profile

TheFridge

10859 posts in 2047 days


#1 posted 10-14-2018 06:59 PM

Most I’ve seen anchor to the bottom mainly.

-- Shooting down the walls of heartache. Bang bang. I am. The warrior.

View John Smith's profile

John Smith

2083 posts in 723 days


#2 posted 10-14-2018 07:12 PM

Dan, I made a bench like you describe years ago and used the standard
8” steel bench vise – I had to mortice out a pocket for the vise to mount properly
under the table. then, a piece of 1×6 oak for the closing part to be flush with the bench top.
the “quick release” mechanism is a nice feature to have.
you can figure it out – it just takes a little bit of “ingenuity”.

.

-- I am a painter. That's what I do. I paint things --

View BlasterStumps's profile

BlasterStumps

1473 posts in 1000 days


#3 posted 10-14-2018 07:13 PM

might help to know more about what holding work you are wanting to do with the vise. Bar Clamps and such can do a lot of different holding jobs. You could even use a hold down for some tasks.

-- "I build for function first, looks second. Most times I never get around to looks." - Mike, western Colorado

View WoodenDreams's profile

WoodenDreams

830 posts in 472 days


#4 posted 10-14-2018 10:22 PM

I installed a vise that John Smith has suggested next to my drill press, inexpensive, very functional for what I use it for and easy to install. I’ve also installed three Grizzly H7788 vises on another bench. Check out different vises online from Rockler, Grizzly, ebay, etc. to compare. Install your wood jaw to the height you need. You could hold you wood to the side of the wood bench with F-clamps to save cost.

View JohnMcClure's profile

JohnMcClure

813 posts in 1201 days


#5 posted 10-15-2018 01:16 PM

Since it’s just temporary while you are on sawhorses, consider this approach:

Using hardware you already have.
And then get a good Eclipse vise once the benchtop is on legs.

The image is from a Woodworker’s Journal tips+tricks book.
Many variations on that theme can be imagined that could even be more permanent and easy to use.

-- I'd rather be a hammer than a nail

View WoodenDreams's profile

WoodenDreams

830 posts in 472 days


#6 posted 10-18-2018 04:17 AM

You may want to check out youtube.com and search “F clamp vise” or “moxon vise”. to get some Ideas. One of the ones I like is by “working with DIY tools”, “How to make a cheapMoxon Vise”. Some are similar to JohnMcClure sugestions.

View AlaskaGuy's profile

AlaskaGuy

5434 posts in 2870 days


#7 posted 10-18-2018 06:50 AM

Add or subtract from the bottom as needed. Or look at portable Moxon vices.

https://youtu.be/TqE-2cPZdL4

-- Alaskan's for Global warming!

View gauntlet21's profile

gauntlet21

69 posts in 771 days


#8 posted 10-18-2018 03:29 PM

Good ideas, I’ll keep on the lookout. For a little more info, I’ll primarily be using the vise to hold wooden pieces that I’m assembling, drilling, cutting, planing, etc. The perfect vise for me is the standard front vise with wooden jaws and a long wooden handle to screw it tight with. I’d have it roughly 18” wide and have a clamping ability of maybe 12” or so. Nothing too fancy, just wanted to know if there was something I hadn’t seen yet that didn’t require clearance beneath the table top.

Thanks again,

Dan

View AlaskaGuy's profile

AlaskaGuy

5434 posts in 2870 days


#9 posted 10-18-2018 05:41 PM



Good ideas, I ll keep on the lookout. For a little more info, I ll primarily be using the vise to hold wooden pieces that I m assembling, drilling, cutting, planing, etc. The perfect vise for me is the standard front vise with wooden jaws and a long wooden handle to screw it tight with. I d have it roughly 18” wide and have a clamping ability of maybe 12” or so. Nothing too fancy, just wanted to know if there was something I hadn t seen yet that didn t require clearance beneath the table top.

Thanks again,

Dan

- gauntlet21


Seems like a moxon vice would work for you. You can make it any lenght you want. It can be clamped to the top of you or mounted flush with you bench or moved to either position easy enough.

This is a photo of mine in both positions.

-- Alaskan's for Global warming!

View shampeon's profile

shampeon

1900 posts in 2744 days


#10 posted 10-18-2018 06:00 PM

Hold up a second here. If I understand your correctly, you want to temporarily mount a vise that sits flush with the face of your unassembled bench. Ok, fine. But you are looking to buy one short term just for this stage? Ooookkkkay. And the vise can’t go underneath the bench top because of how you are holding it temporarily? You’ve now totally lost me.

The end of the table can overhang your base, even a sawhorse, by a couple of feet. So mount the vise you ultimately want to use with your fully assembled bench to the face or the end of your bench top.

I wouldn’t bother mortising the top to fit the inner face of the vise or anything like that. Just mount it proud of the bench temporarily while you finish your base. Use a couple pieces of scrap for the jaws to bring them up to the level of the table.

Moxon vises are great, you should totally make one if you want. But this all sounds like a distraction. Buy the vises you are going to use on the workbench and get busy making the base.

-- ian | "You can't stop what's coming. It ain't all waiting on you. That's vanity."

View Smitty_Cabinetshop's profile

Smitty_Cabinetshop

16258 posts in 3179 days


#11 posted 10-18-2018 09:43 PM

^ I was wondering many of the same things (just too lazy to type it up). Thanks ian!

-- Don't anthropomorphize your handplanes. They hate it when you do that. -- OldTools Archive --

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com