LumberJocks

All Replies on Hinge placement

  • Advertise with us
View BB1's profile

Hinge placement

by BB1
posted 09-30-2018 02:12 AM


7 replies so far

View CWWoodworking's profile

CWWoodworking

528 posts in 721 days


#1 posted 09-30-2018 02:38 AM

No rules. Your doors are borderline needing 3 hinges. If they are fitting good, I would just use 2.

When I used hinges like that, I went down/up about 3”

View Jim Jakosh's profile

Jim Jakosh

23552 posts in 3647 days


#2 posted 09-30-2018 02:53 AM

2-3” for a door that high is good as long as it is not warped.

-- Jim Jakosh.....Practical Wood Products...........Learn something new every day!! Variety is the Spice of Life!!

View BB1's profile

BB1

1473 posts in 1390 days


#3 posted 09-30-2018 03:29 AM

Thank you both for the replies. When I was looking at location for visual appeal, I think I was around that distance. And thankfully the door is very flat – no warp (1/4 inch plywood with oak frame).


No rules. Your doors are borderline needing 3 hinges. If they are fitting good, I would just use 2.

When I used hinges like that, I went down/up about 3”

- CWWoodworking


2-3” for a door that high is good as long as it is not warped.

- Jim Jakosh


View splintergroup's profile

splintergroup

3007 posts in 1764 days


#4 posted 09-30-2018 02:57 PM

As said, no rules 8^) BUT I have read some design books that mention aligning the outboard edges of the hinges with the top of the rails (these were small cabinet doors, about 12” high). In you case, the rails are relatively thin and I think the location you show looks perfectly fine and is a good support choice for a door of that length. If you were to use three hinges to control warping, I’d probably recommend moving the top/bottom hinges out 1” more.

Either way, it all comes down to what looks good and your setup looks good!

View 000's profile

000

2859 posts in 1441 days


#5 posted 09-30-2018 03:16 PM

I always put mine at 3”

Go take a look at your kitchen doors and see where they have them.

View Nubsnstubs's profile

Nubsnstubs

1626 posts in 2272 days


#6 posted 09-30-2018 03:40 PM

I’ve always done mine at 4”. Don’t have a clue why, but that’s what I settled on years ago. I also use the European style hidden hinges, even though I still have about a hundred pair of Amerock hinges like you are going to use.

I thought those hinges went extinct when the European hinges first hit the continent, something like the Native Americans almost did at first contact with Europe…............ Jerry (in Tucson)

-- Jerry (in Tucson) www.woodturnerstools.com

View BB1's profile

BB1

1473 posts in 1390 days


#7 posted 09-30-2018 11:36 PM

Got the hinges installed and a knob. Much thanks for all the replies. Still working on some stands that these will be placed on. Hope to have the whole Murphy bed and side cabinets ready for a project post sometime in October. Has been a bigger project than I imagined!!

These are actually opposite of final…knobs will be on side nearest murphy bed (which will be in the center)

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com