LumberJocks

All Replies on Template Routing

  • Advertise with us
View EdsCustomWoodCrafts's profile

Template Routing

by EdsCustomWoodCrafts
posted 09-23-2018 07:42 PM


6 replies so far

View Bill White's profile

Bill White

5225 posts in 4440 days


#1 posted 09-23-2018 08:56 PM

Yes you can use a straight bit. Just remember that you’re not building fine furniture. It is a sharpening station.
Clean up the corners and get to sharpening.
You did not state what wood you’ll be using.

-- [email protected]

View jerryminer's profile

jerryminer

960 posts in 1921 days


#2 posted 09-23-2018 09:34 PM

A 2-inch bit doesn’t extend beyond the template bushing? I think you’re not getting the full-depth plunge from your router.

But, yes, a straight bit will do it. How deep are you trying to go? A very shallow recess will keep the stones from sliding around (a cleat on top of the surface might be easier to do and make it easier to clean up the sharpening sludge)

-- Jerry, making sawdust professionally since 1976

View EdsCustomWoodCrafts's profile

EdsCustomWoodCrafts

931 posts in 1823 days


#3 posted 09-23-2018 11:11 PM



A 2-inch bit doesn t extend beyond the template bushing? I think you re not getting the full-depth plunge from your router.

But, yes, a straight bit will do it. How deep are you trying to go? A very shallow recess will keep the stones from sliding around (a cleat on top of the surface might be easier to do and make it easier to clean up the sharpening sludge)

- jerryminer

You may be right I need to check, I tkiught about a cleat but thought it would be cool to try recessing as I have never done it before… I’m hiding a scrap piece of oak I have lying around . As for the depth probably less than 1/4” deep

-- Thanks Ed “A bad day woodworking is better than a good day working. ~Author unknown” . Come check out my website for more about what I make and how at www.edscustomwoodcrafts.com

View EdsCustomWoodCrafts's profile

EdsCustomWoodCrafts

931 posts in 1823 days


#4 posted 09-23-2018 11:12 PM



Yes you can use a straight bit. Just remember that you re not building fine furniture. It is a sharpening station.
Clean up the corners and get to sharpening.
You did not state what wood you ll be using.

- Bill White

I’m using a scrap piece of 4/4 red oak I had lying around

-- Thanks Ed “A bad day woodworking is better than a good day working. ~Author unknown” . Come check out my website for more about what I make and how at www.edscustomwoodcrafts.com

View Kirk650's profile

Kirk650

663 posts in 1228 days


#5 posted 09-24-2018 02:12 AM

I use an MDF ‘board’ with cleats to hold the stones (diamond plates, in my case). Works great, but getting nasty looking after a few years.

View EdsCustomWoodCrafts's profile

EdsCustomWoodCrafts

931 posts in 1823 days


#6 posted 09-24-2018 03:58 AM


I use an MDF ‘board’ with cleats to hold the stones (diamond plates, in my case). Works great, but getting nasty looking after a few years.

- Kirk650


I am using a solid oak panel that also sits on cleats and if it gets all dinged up I’ll just remake the top

Here is a picture with the frame glued up

-- Thanks Ed “A bad day woodworking is better than a good day working. ~Author unknown” . Come check out my website for more about what I make and how at www.edscustomwoodcrafts.com

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com