LumberJocks

All Replies on Shop countertops

  • Advertise with us
View Sparks500's profile

Shop countertops

by Sparks500
posted 09-13-2018 09:08 PM


9 replies so far

View Redoak49's profile

Redoak49

4007 posts in 2384 days


#1 posted 09-13-2018 09:12 PM

I used a couple short counter sunk screws instead of glue. For finish I used shellac and then wax.

View mathguy1981's profile

mathguy1981

93 posts in 300 days


#2 posted 09-13-2018 09:39 PM

Don’t use glue. I’ve used hardboard as a “replaceable” top before, and used 1” countersunk screws, worked like a charm.

-- Two thumbs and counting

View Woodknack's profile

Woodknack

12817 posts in 2776 days


#3 posted 09-13-2018 11:43 PM

Hide glue. Ones of it’s qualities is that is can be reheated and the parts taken apart.

-- Rick M, http://thewoodknack.blogspot.com/

View WoodenDreams's profile

WoodenDreams

610 posts in 307 days


#4 posted 09-15-2018 08:37 AM

Counter sunk screws without glue may by your best option. But if you use glue, Hyde Glue is really the only glue that you can dismantle, just by using a heat gun. Also Hyde Glue will stick to Hyde glue. That’s where I got my 24”x8’ laminated bench top. but I use I as a gluing and clamping table. Easy to remove glue off the lamination.

View Planeman40's profile

Planeman40

1413 posts in 3157 days


#5 posted 09-15-2018 03:19 PM

Yep, keep the hardboard tops removable and I recommend polyurethane as a finish, not shellac. Shellac is a great finish, however it uses alcohol as a solvent. Should you ever drop or spill alcohol on it it will melt. Polyurethane is tougher and more resistant to solvents.

-- Always remember: It is a mathematical certainty that half the people in this country are below average in intelligence!

View bondogaposis's profile

bondogaposis

5416 posts in 2747 days


#6 posted 09-15-2018 09:34 PM

I guarantee that if you glue it, no matter what type of glue, you will never replace it. It would be far easier to make a new top than to try and separate a glued down top, even hide glue. Use screws, and then the top will be easily replaceable, if you are worried about dinging a chisel or a plane use brass screws.

-- Bondo Gaposis

View 000's profile

000

2859 posts in 1295 days


#7 posted 09-15-2018 09:39 PM

Use melamine, or cover any substrate (PB, MDF, Ply) with plastic laminate. (formica,etc…)
It will last years and years, you wont have to change it.

View MrUnix's profile

MrUnix

7388 posts in 2595 days


#8 posted 09-15-2018 11:16 PM

+1 ^^
I have always preferred laminate (Formica) over hardboard. Much more durable than hardboard, doesn’t soak up liquids (like stains or paint), easily cleaned … and you can get whatever look you want, from marble/stone to wood/butcherblock, or just plain solids. Put down with contact cement, it will stay put – but is still relatively easy to replace decades down the road if needed.

Cheers,
Brad

-- Brad in FL - In Dog I trust... everything else is questionable

View Sparks500's profile

Sparks500

254 posts in 726 days


#9 posted 09-16-2018 01:29 AM

Ok, I was going back and forth, all good suggestions by all of you, went with simple: sheet of MDF with an overlay of white hardboard. Didn’t even know they made white hardboard, and its in stock at HD. 10 bucks a sheet, with 18 for the MDF with a little hide glue around the edges.
Formica would be great, but, I like the idea off running a screw into the top to fasten something down temporarily and not worry about it.
plus, it follows my motto: Easy, cheap, and fast….
Thanks to all of you.

-- A good day is any day that you're alive....

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com