LumberJocks

All Replies on Stable or Not...

  • Advertise with us
View ScottM's profile

Stable or Not...

by ScottM
posted 02-13-2018 01:45 PM


11 replies so far

View RobHannon's profile

RobHannon

321 posts in 1073 days


#1 posted 02-13-2018 02:01 PM

Not sure how often she may need to disassemble the table, but I would worry about pocket screws being used in place of knock down hardware.

As far as the stability goes I would certainly add something either to the lower ends or perhaps a support across the middle. Maybe a wide piece with a cutout to match the relief cut in the upper and lower apron pieces.

View dhazelton's profile

dhazelton

2839 posts in 2839 days


#2 posted 02-13-2018 02:21 PM

I see the leg assemblies splaying outward. I’d put a cross member down low, or one at each end.

View  woodshaver Tony C   's profile

woodshaver Tony C

6930 posts in 3896 days


#3 posted 02-13-2018 02:22 PM

I would add across brace about half way down from the top. That should make the legs more stable.

-- St Augustine FL, Experience is the sum of our mistakes!

View rbrjr1's profile

rbrjr1

208 posts in 748 days


#4 posted 02-13-2018 02:40 PM

keep the shelf and move the bottom of it down to about 2” off the floor.

she says she doesn’t need the shelf, you can remind her of it every time you go to her house and she has things stacked on it.. lol

-- only an idiot dismisses an intelligent statement because they dont know anything about the person delivering it.

View ScottM's profile

ScottM

745 posts in 2689 days


#5 posted 02-13-2018 03:34 PM



keep the shelf and move the bottom of it down to about 2” off the floor.

she says she doesn’t need the shelf, you can remind her of it every time you go to her house and she has things stacked on it.. lol

- rbrjr1

Ya know, I’m starting to lean more that way…. Just keep it for the strength the legs need and I know she’ll need a place to put more crap. I’m still thinking on it….

View Loren's profile

Loren

10477 posts in 4191 days


#6 posted 02-13-2018 03:43 PM



I see the leg assemblies splaying outward. I d put a cross member down low, or one at each end.

- dhazelton

Agree.

View GR8HUNTER's profile

GR8HUNTER

6602 posts in 1255 days


#7 posted 02-13-2018 03:46 PM

I would put one in matching the same profile as front and rear :<))

-- Tony---- Reinholds,Pa.------ REMEMBER TO ALWAYS HAVE FUN

View Snipes's profile

Snipes

438 posts in 2787 days


#8 posted 02-13-2018 04:22 PM

I prefer no shelf also, they seem to just collect clutter.. I agree with others on crossmember, or how about just one in center.

-- if it is to be it is up to me

View LesB's profile

LesB

2223 posts in 3986 days


#9 posted 02-13-2018 06:11 PM

One possibility that would work is to make double sided legs so you get support in both directions at the top. It is not as good as stretchers lower down but it should work and you can always add a shelf later. It involves mitering the corner where the two parts meet to give it a clean appearance, tapering the leg pieces to the bottom and making the compound angle cuts at the top and bottom of the legs to get the angles in you illustration.
I drew a quick example in the attached image.

-- Les B, Oregon

View pete724's profile

pete724

70 posts in 1352 days


#10 posted 02-14-2018 01:26 PM

I gotta go with Woodshaver Tony.

Just add an additional “end apron” at the bottom.

or partway up or halfway up…........

View ScottM's profile

ScottM

745 posts in 2689 days


#11 posted 02-14-2018 03:04 PM



I gotta go with Woodshaver Tony.

Just add an additional “end apron” at the bottom.

or partway up or halfway up…........

- pete724

Yeah, I think that’s what I’ve decided. This is my new plan. GR8HUNTER (also Tony) suggested adding the same profile cutout to them. I’ll secure them with some threaded inserts and connecting bolts. Same with the top aprons instead of pocket screws.

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com