All Replies on Jointer Help

  • Advertise with us
View Rayman24's profile

Jointer Help

by Rayman24
posted 02-06-2018 11:18 PM

6 replies so far

View TheFridge's profile


10861 posts in 2372 days

#1 posted 02-06-2018 11:33 PM

If you have space don’t do benchtop and skip a 6” jointer and go to 8” unless a 6” will handle almost all the stock you run through it.

-- Shooting down the walls of heartache. Bang bang. I am. The warrior.

View eflanders's profile


329 posts in 2736 days

#2 posted 02-06-2018 11:50 PM

In your budget range, I’d be shopping classified ads for a floor standing 6”-8” unit. Helical/spiral heads are great for highly figured and reclaimed lumber. But they are hard to find used. The straight blades actually cut to finer finish and have been happily used for decades. 6”, 8” or wider? Here’s my two cents worth based on the information you already provided: When building large width projects, you don’t want to glue boards together more than 6” wide or you’ll have movement issues. So a 6” jointer is fine IF you don’t buy rough sawn lumber. Why? Because sawyers often cut boards as wide as they can to maximize profits. When you buy rough sawn stock, one of the very first things to do is to joint a face, then an edge before ripping that board to the desired width. So where do you buy or get your lumber? That answer tells you what width jointer to shop for. Good luck!

View AZWoody's profile


1478 posts in 2110 days

#3 posted 02-06-2018 11:54 PM

Definitely get the spiral head if you can. It will really help to reduce tearout so less board waste. Also, the carbide segments last a long time. Lastly, setup time is greatly reduced to basically making sure everything is aligned when you buy it and then you don’t have to worry about having to align the blades every time you change to new knives.

Then, there is reduced noise as well.

View Kelster58's profile


759 posts in 1426 days

#4 posted 02-07-2018 01:40 AM

I was in the same boat as you last year. I have a small shop and small budget. I put the money together to get a jointer. After looking at bench tops and used models I decided to splurge and go new.

I have the Grizzly 6” with Spiral Cutter head(G0452Z) Worth every penny for the spiral cutter head….

Totally agree with TheFridge….don’t get a bench top.

-- K. Stone “Tell me and I forget, teach me and I may remember, involve me and I learn.” ― Benjamin Franklin

View msinc's profile


567 posts in 1390 days

#5 posted 02-07-2018 04:39 AM

All of the above is good solid advice….now when you find all these 8” jointers with a spiral cutter head for $500 please let me know, I’d like to have one too!!!

View Breeze73's profile


102 posts in 1567 days

#6 posted 02-07-2018 09:03 AM

I would agree that you should just keep an eye out for an 8” jointer to come available in your area on CL. I have a 6” Jet and I wish I had gotten an 8”. That extra 2” makes a huge difference. The Grizzly G0490 looks to be a great machine, but it is outside your budget brand new. You should be able to eventually find one for $600-$700.

WRT the blades, if you go with a used 8”, just stick with the cutterhead that comes with it. If it is a Grizzy, Jet, PM, Delta, or other well known brand, you can always upgrade to the shelix head at a later time. Obviously the sooner the better as setting up straight knives after sharpening is a PITA. But it becomes easier the more times you do it.

I would not recommend a benchtop jointer. They work. But they are extrememly limiting.

-- Breeze

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics