LumberJocks

All Replies on Looking to get a jointer

  • Advertise with us
View Tom's profile

Looking to get a jointer

by Tom
posted 02-04-2018 07:00 PM


11 replies so far

View Hermit's profile

Hermit

238 posts in 1865 days


#1 posted 02-04-2018 09:59 PM

I purchased about a month ago the 6 inch cutech with carbide tips.its been a great little machine. Bought it off Amazon. My projects will all be smaller in size so I opted for a bench top. For me, comfortably is no longer than 4 feet in length unless you have infeed/outfeed supports. The fence is so so and there’s room for improvement there but it works for me. It’s stable enough so it doesn’t have to be bolted down but light enough if you want to store it when not in use.i don’t regret not getting the 8 inch just depends on what you’ll be using it for.

-- I'm like the farmer's duck. If it don't rain, I'll walk.

View MikeNolan's profile

MikeNolan

11 posts in 651 days


#2 posted 02-04-2018 10:03 PM

For me longer is more important than wider.
Also I would look at “left in the rain for 5 years” if it was close enough to me. Rust is often easy to remove. Pits in a jointer surface don’t matter much. If the rust stops the motor from spinning I would pass on it.

View Bill White's profile

Bill White

5228 posts in 4500 days


#3 posted 02-04-2018 10:07 PM

I have the Cutech 6”. Works great for smaller projects. The spiral head is a BIG plus.
Bill

-- [email protected]

View Marlow's profile

Marlow

186 posts in 3210 days


#4 posted 02-04-2018 10:15 PM

Skip the bench top jointers: go for a 6” jointer on Craigslist. I started out with a Jet 6” and it was excellent.

View bbasiaga's profile

bbasiaga

1243 posts in 2535 days


#5 posted 02-05-2018 12:37 AM

The first rule of jointer advice is:

1. Get the widest one you can

The corrolary to this rule is:
-You will always have a board wider than your jointer.

So get what fits in your space. I had the SHopfox 6” with straight knives, and I liked it a lot I just outgrew it. Like Mike said, it was the length that got me more than the width. In fact, I still have a 6” jointer, just a floor standing longer one.

The advantage of some of the 8” ones is that they have longer beds. You can also look at the combo machines, if you don’t already have a planer.

Brian

-- Part of engineering is to know when to put your calculator down and pick up your tools.

View knotscott's profile

knotscott

8343 posts in 3915 days


#6 posted 02-05-2018 11:47 AM

My shop is half of a two car garage. It can be tight, but with a good layout a stationary jointer can fit. The actual difference in square footage is pretty minimal, but the torque, mass, and rigidity of a stationary unit are notably superior, not to mention they’re much quieter.

My usable shop is essentially the left half of the pic below:

-- Happiness is like wetting your pants...everyone can see it, but only you can feel the warmth....

View Steve's profile

Steve

1614 posts in 1122 days


#7 posted 02-05-2018 02:40 PM

It depends on how long you want to wait to buy a jointer. You could be chasing a decent jointer on CL for months. I responded to a Jet 6” long bed 35 mins after it was posted and by the time the seller got back to me it was already sold.

So I’m actually looking at the 8” spiral Cutech. Seems to be a pretty good machine for a benchtop.

View Knockonit's profile

Knockonit

613 posts in 742 days


#8 posted 02-05-2018 03:14 PM

I have a couple jointers, both are 6’’ although one it a small table top unit, which i use for a lot of stuff. while it has a short bed, it fills its need, the other is a HF unit, took some time to tune it, and get squared away, but again it doesnt have the longest table around, but with a little finese again does the job.
And as noted, no matter the width of jointer, the boards you need to clean up are always gonna be bigger than what you have. just the way it is.
good luck
rj

View bilyo's profile

bilyo

882 posts in 1642 days


#9 posted 02-05-2018 03:35 PM

I suggest that you do a search for discussions on this forum and others regarding the use of a planer with sled vs a jointer for straightening/flattening rough cut lumber. There have been numerous opinions expressed on the subject that you might find useful in making your decision. Also, check out Utube videos on the use of planers with sleds and jointers.

IMO, if you are dealing with space and/or budget concerns, a planer is the best first purchase. A jointer is good for making the first side flat, but it is difficult to make the opposite side flat and parallel. A planer can also make the initial side flat using a sled and can do so for a board up to about 12” wide. And, of course, it easily makes the opposite side flat and parallel. You can then use a well tuned table saw to square up the edges.

View ChrisK's profile

ChrisK

2038 posts in 3621 days


#10 posted 02-05-2018 03:44 PM

I have a 6” Jet, 14 years now, still runs fine. Just do not try and run a build up of plywood with screws in it through the planer, really mess up the blades. Did not slow the motor down on bit.

-- Chris K

View Tom's profile

Tom

182 posts in 1600 days


#11 posted 02-05-2018 03:50 PM

I’ve been scouring my local CL daily…sometimes 2x but haven’t found (or been first) on the rare deal that comes across. There was one of the Porter Cable bench top for $100 and it was almost new but that was gone before I saw the ad.

I’m leaning toward one of the 8” Cutech jointers. My wall space is shelving, cupboards, or my workbench and there isn’t a good way to re-organize it all due to where the power outlets are…and where I have my dust collector set up. I don’t do large projects and if I do need to do longer boards I’ll rig up some temporary supports…or make my son’ help me.

I do have a planer and have used a sled to flatten boards…it’s just the lumber i have now isn’t straight on the edges and my table saw with an edge sled doesn’t work with 8/4 lumber.

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com