LumberJocks

All Replies on 3hp/60 gal 12.6 CFM @40 PSI; 11.3 @90 - Enough to spray stains?

  • Advertise with us
View e_dogg's profile

3hp/60 gal 12.6 CFM @40 PSI; 11.3 @90 - Enough to spray stains?

by e_dogg
posted 02-02-2018 12:06 PM


7 replies so far

View Carloz's profile

Carloz

1147 posts in 951 days


#1 posted 02-02-2018 12:30 PM

No tangible investment needed. Get yourself this gun from harbor freight and be done with it. For the saved $$275 you can buy me e beer.

View tomsteve's profile

tomsteve

934 posts in 1578 days


#2 posted 02-02-2018 12:41 PM

i have a 3 hp 60 gallon twin cylinder( not 2 stage) and have successfully painted many vehicles with it using a devilbiss finishline gun and a devilbiss copper tekna. ive used both guns for finishing entertainment centers, computer desks, kitchen cabinets, and much more. if you had the budget of 2-300 for a gun, id suggest the devilbiss finishline 4. you can get a “kit” with 3 different fluid tips.
http://www.tptools.com/DeVILBISS-Finishline-FLG-4-HVLP-Finish-Gun-Kit,7172.html

this is the filter i use
http://www.tptools.com/SearchResult.aspx?searchPhrase=devilbiss%20120%20cfm%20filter%20regulator

i suggest a regulator at the gun,too.

it will work great for what youre doing once ya get the hang of gun set up and spraying technique.

after using it, you may find many more projects you can spray with them. might even get into a little auto body work/repair.

View Tennessee's profile

Tennessee

2901 posts in 2874 days


#3 posted 02-02-2018 01:51 PM

I own a 30 gallon, 5HP (debatable) 220VAC Coleman compressor that I bought back in the late 90’s.
I have sprayed everything from water based stain on flower boxes, automotive paint, up to air brushing.

I use the purple guns shown above from HF, and they do just fine. I have two air brushing units, one expensive one, very old and desirable, (can’t remember the name), and one from HF. Can’t tell the difference in application, to be honest.

I have it piped for two lines, one that is a straight run for things like blow guns, filling tires, full pressure of 115 lbs., and one line that has a regulator/water separator on it, set at 40 lbs. for spray. Two coils of line mounted on the wall above in those HF type roll-up units, save that the spray unit has a lighter poly hose on it, just for ease of use.

I clean the filter about once a quarter, and change the oil about every other year, depending on what it looks like when I pull the little dipstick. I only put in non-detergent synthetic. I drain any water out of the tank at least once a year.

I probably have less than $400 in the whole rig, and it has served me well, from filling tires to spraying sunbursts on guitars.

-- Tsunami Guitars and Custom Woodworking, Cleveland, TN

View e_dogg's profile

e_dogg

5 posts in 496 days


#4 posted 02-02-2018 08:28 PM

I appreciate the advice from everyone, it sounds like ill be shopping for a spray gun. While I had a max of 2-300$ I certainly wouldn’t mind spending less. Maybe I should give that HF unit a try, what nozzles and tips are y’all using with it?

View MrUnix's profile (online now)

MrUnix

7358 posts in 2558 days


#5 posted 02-02-2018 08:54 PM

I appreciate the advice from everyone, it sounds like ill be shopping for a spray gun. While I had a max of 2-300$ I certainly wouldn t mind spending less. Maybe I should give that HF unit a try, what nozzles and tips are y all using with it?
- e_dogg

For $10 you can’t beat that little purple gun. And it only has 1 need/tip (1.4mm IIRC), so you are stuck with that. I have not found that to be a big deal, as you just thin appropriately if needed. Outstanding for spraying oil based enamels, which are much thicker than stain – so you should not have any problems at all. And if you don’t like it, then you are not out much cash.

Cheers,
Brad

-- Brad in FL - In Dog I trust... everything else is questionable

View William Shelley's profile

William Shelley

609 posts in 1828 days


#6 posted 02-02-2018 09:49 PM

You’d be better off buying several spray guns and dedicating them for specific types of finish instead of spending a lot on one spray gun. All it takes is one forgetful moment where you leave something in the gun too long and it gunks it all up to potentially ruin it.

-- Woodworking from an engineer's perspective

View TungOil's profile

TungOil

1205 posts in 854 days


#7 posted 02-03-2018 12:37 AM

You have more than enough compressor to run a HVLP or conversion gun. +1 on the Devilbiss gear, it is very good quality and you get a wide selection of tips and needles to select from. I spray dye stain and lacquer from my gravity feed Devilbiss gun on 7 CFM no problems. You can also add decups if you prefer disposable cups.

I have this one: DeVilbiss (GFG670) Plus High Efficiency Gravity Feed Spray Gun https://www.amazon.com/dp/B0002SQYB4/ref=cm_sw_r_cp_tai_9pqDAbFCZVS8M

-- The optimist says "the glass is half full". The pessimist says "the glass is half empty". The engineer says "the glass is twice as big as it needs to be"

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com