LumberJocks

All Replies on height vrs base diameter for a table lamp ??

  • Advertise with us
View Abter's profile

height vrs base diameter for a table lamp ??

by Abter
posted 01-30-2018 12:09 AM


5 replies so far

View clin's profile

clin

1027 posts in 1360 days


#1 posted 01-30-2018 01:46 AM

The shape of the lamp makes no difference, beyond the width of the base. It would matter if your were dealing with a moving object, but this is a static problem. Assuming it is symmetric, the center of mass will be in the middle. Makes no difference how wide it is.

As you already mentioned, more mass (weight) lower down make it more stable. There may very well be some standard, but it would be more complicated than simply height to base width as the weight distribution up and down is critical.

I’d suggest you mock up a prototype, and play around with it. Get a sense for how easy or hard it is to knock over. My experience with lamps is not some much you knock the lamp as you bump into the end table it is sitting on.

It is also common to have weight in the base of the lamp, just to make it more stable. So perhaps incorporate that into your design. Heavy metal or even just sand near the bottom would go a long way to making it more stable.

-- Clin

View woodbutcherbynight's profile

woodbutcherbynight

5964 posts in 2773 days


#2 posted 01-30-2018 03:51 AM

The mock up idea is a good one. I used this during my build of two lamps for my kids. As this was for kids I made sure the base was heavy. The daughters lamp has a wide square base to accommodate the rotating picture frame cube. Knowing this would be played with I overbuilt…. LOL For my sons I used a drum from a transmission at work, plenty heavy at the base.

-- Live to tell the stories, they sound better that way.

View Wildwood's profile

Wildwood

2626 posts in 2499 days


#3 posted 01-30-2018 09:43 AM

You have all kind of parts can add to the base of a lamp to keep it from being knock over. Lot has to with design and your personal choice. You can also improvise and use your imagination like previous posters mentioned.

You can buy metal cast metal stands winch will increase height of the lamp. Or buy clear acrylic, cast brass, or steel lamp bases which are internal at base of the lamp.

These cast iron loades are the best internal parts for base for any floor or table lambs.

http://www.mylampparts.com/Departments/WEIGHTS/CAST-IRON-LOADER.aspx

If look at my pine lamps on my project page, none have any of those components. Except for neck part hollowed out other parts hoping the thicker longer base would be enough and it worked out for the most part. Think could have used cast iron loader for more stability.

-- Bill

View Abter's profile

Abter

75 posts in 991 days


#4 posted 01-30-2018 04:13 PM

thanks everybody…this is exactly the discussion I was hoping for !

You folks are really helping me think clearly about this issue. Wildwood; the loades are a great idea! I never knew such things existed.. They are at the top of my idea list right now.

-- "Many men fish all their lives without ever realizing that it is not the fish they are after." {often mis-quoted as by H.D. Thoreau}

View Steve Peterson's profile

Steve Peterson

405 posts in 3446 days


#5 posted 01-30-2018 07:59 PM

You can also use weight lifting plates that should be much cheaper than the loader weights. 2.5 lb weights should be around 5” in diameter. The only difference is that there is no channel for the power cord.

-- Steve

Have your say...

You must be signed in to reply.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com