a box that is different and EASY

  • Advertise with us
Project by dgreen50 posted 06-30-2013 08:06 PM 31118 views 52 times favorited 18 comments Add to Favorites Watch

Macacuba candle box with split hinged top. Walnut lift tabs. Lacquer finish. Simple but fun box to make. Hinges are 1/8 brass rods

18 comments so far

View goodinwood's profile


27 posts in 2552 days

#1 posted 06-30-2013 08:42 PM



View Albe's profile


225 posts in 2464 days

#2 posted 06-30-2013 09:24 PM

Very nice idea i love the hinged top and the grain alignment.

-- Be yourself everyone else is already taken.

View robscastle's profile


6273 posts in 2657 days

#3 posted 06-30-2013 11:15 PM

I like it
Nice design, nice choice of timber overall a very unique job!
Good work

Robert Brennan

-- Regards Rob

View gfadvm's profile


14940 posts in 3143 days

#4 posted 07-01-2013 12:35 AM

A nice clean design executed with some very cool wood. Good job!

-- " I'll try to be nicer, if you'll try to be smarter" gfadvm

View aussiedave's profile


3114 posts in 2277 days

#5 posted 07-01-2013 12:51 AM

Nice looking box…have never seen one open from the sides like that…very cool….great work.

-- Dave.......If at first you don’t succeed redefine success....

View Dave777's profile


303 posts in 4522 days

#6 posted 07-01-2013 02:16 AM

Looks great to me

-- the stone rejected by the builders will become the capstone

View madts's profile


1903 posts in 2793 days

#7 posted 07-01-2013 04:02 AM

way nice Sir.

-- Thor and Odin are still the greatest of Gods.

View widdle's profile


2072 posts in 3452 days

#8 posted 07-01-2013 04:45 AM

Realy nice clean design as mentioned above…Would like to try to make one of these.. Do the ends of the lid and the two sides have rabbets ?

View 489tad's profile


3625 posts in 3464 days

#9 posted 07-01-2013 11:04 AM

I really like that box.

-- Dan, Naperville IL, I.G.N.

View dgreen50's profile


101 posts in 2794 days

#10 posted 07-01-2013 01:34 PM

For Widdle
The front and back of the box do have a rabbet down each side the thickness of the top. The sides only come up to the
top of the rabbet_ on the front and back ( to give clearance for the top to swing open). Also the top’s ends that meet the sides of the box are rounded over with a 1/4 inch round-over bit on the underside to allow the tops to open without interference.

thx for the comment.

View stefang's profile


16711 posts in 3787 days

#11 posted 07-01-2013 06:34 PM

Simply beautiful. Great wood wisely used and a great design too.

-- Mike, an American living in Norway.

View bannerpond1's profile


397 posts in 2351 days

#12 posted 07-02-2013 07:17 PM

Fine looking box, dgreen. Would you give me your source for the brass rods? Thanks

[email protected]

-- --Dale Page

View Fishinbo's profile


11362 posts in 2629 days

#13 posted 07-02-2013 09:15 PM

Neat and classy box! Like the hinged top and the pulls. The pretty grains really pop with the finish. Well done!

View Rotceh's profile


231 posts in 3900 days

#14 posted 07-02-2013 09:36 PM

nice and clean desing. I like this box!!!

-- Work is my road to knowledge,Curiosity is my fellow traveler. El trabajo es mi camino al conocimiento, la curiosidad es mi compañero de viaje. Héctor

View Boxguy's profile


2841 posts in 2720 days

#15 posted 07-04-2013 03:51 AM

Dgreen, like your the design you used in this box. It is wonderfully symmetrical and neatly made. The wood choice is a knock out. I may have to make my version of of your box in your honor. The design intrigues me. Your jewelry box was very well done, but this is my favorite so far. Thanks for sharing your work with us. Keep boxing and keep posting.

-- Big Al in IN

showing 1 through 15 of 18 comments

Have your say...

You must be signed in to post the comments.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics