LumberJocks

Segmented Bowl of Walnut, Maple and Poplar

  • Advertise with us
Project by adot45 posted 09-08-2021 11:59 AM 436 views 0 times favorited 12 comments Add to Favorites Watch

My first segmented ring bowl. I followed the instructions from the book by Don Jovag. I had to make a small change to the design ring when I messed up the spacer rings by not clamping them up properly and the outer edges splayed open and I couldn’t save them.

After that goof up on my part everything went pretty well. Pretty much glue em up, true em up, and stack em up. Then turned it and glued up the bottom.
Finish is 3 coats of Salad Bowl Finish by General. This project was enjoyable and a lot of fun. Thanks for looking.

-- “Often wrong but never in doubt”. Dave in WV.





12 comments so far

View jeff's profile

jeff

1383 posts in 4685 days


#1 posted 09-08-2021 12:10 PM

Nice looking bowl there Dave. When I mess up a project it almost throws me over the edge lol. Nice recovery.

-- Jeff,Tucson,Az.

View Dave Polaschek's profile

Dave Polaschek

8297 posts in 1802 days


#2 posted 09-08-2021 12:16 PM

Came out looking good, Dave! Well done!

-- Dave - Santa Fe

View BobWemm's profile

BobWemm

3015 posts in 3146 days


#3 posted 09-08-2021 12:43 PM

Very Impressive, Love it.

Bob

-- Bob, Western Australia, The Sun came up this morning, what a great start to the day. Now it's up to me to make it even better. I've cut this piece of wood 4 times and it's still too damn short.

View Lazyman's profile

Lazyman

7836 posts in 2608 days


#4 posted 09-08-2021 01:00 PM

That is great. One if these days I may have to try making a segmented bowl.

-- Nathan, TX -- Hire the lazy man. He may not do as much work but that's because he will find a better way.

View pottz's profile

pottz

20258 posts in 2204 days


#5 posted 09-08-2021 01:37 PM

beautiful bowl,love that design.

-- working with my hands is a joy,it gives me a sense of fulfillment,somthing so many seek and so few find.-SAM MALOOF.

View 987Ron's profile

987Ron

2019 posts in 537 days


#6 posted 09-08-2021 03:55 PM

Nice design and choice of woods…makes for a great bow. Good workmanship.

-- Ron

View Peteybadboy's profile

Peteybadboy

3906 posts in 3170 days


#7 posted 09-08-2021 09:33 PM

Wow nice job!

-- Petey

View adot45's profile

adot45

354 posts in 1844 days


#8 posted 09-08-2021 09:34 PM

Thank you to all you guys. I appreciate your comments.

I’m milling lumber for my next one and also ordered a new lathe that has reverse from Woodcraft.

-- “Often wrong but never in doubt”. Dave in WV.

View recycle1943's profile

recycle1943

5817 posts in 2842 days


#9 posted 09-09-2021 12:13 PM

impressive design – great job

-- Dick, Malvern Ohio - my biggest fear is that when I die, my wife sells my toys for what I told her I paid for them

View MovingChips's profile

MovingChips

477 posts in 461 days


#10 posted 09-09-2021 06:15 PM

Love the pattern

View RyanGi's profile

RyanGi

81 posts in 257 days


#11 posted 09-12-2021 03:07 AM

Nice! Did you use hose clamps for gluing/clamping the segments together or tape?

-- Ryan/// I like chips...and sawdust...but mostly chips...with vinegar

View adot45's profile

adot45

354 posts in 1844 days


#12 posted 09-12-2021 10:50 AM



Nice! Did you use hose clamps for gluing/clamping the segments together or tape?

- RyanGi

Hi Ryan, I use 2 6” hose clamps put together, this way I can tighten it on the segment ring from 2 directions.

-- “Often wrong but never in doubt”. Dave in WV.

Have your say...

You must be signed in to post the comments.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com