Finished Fence

  • Advertise with us
Project by ToddE posted 06-29-2010 04:33 AM 4031 views 14 times favorited 26 comments Add to Favorites Watch

Well, I finally finished the fence I threatened to build. Basically, it gave me almost 6’ to the right and 28” to the left. I used 1/2 UHMW for the sides of the fence and they are slick. The fence wound up to be 46” long from front to back. It was a fun project and I have been busy rearranging my shop to get a better work flow. Shop is getting smaller as tool count increases. The back was kind of a pain in the butt, but I was nothing a grinder couldn’t handle. Plan on putting a router on the right side table, but I went to Rockler in Buffalo and about fell on the floor when I saw how much they wanted for a router lift and it didn’t even include the plate. So I will put a regular plate in and do it the ol’ fashion way for a while. The saw is a Ridgid 3612. Just a couple little things I am going to do, but other than that its pretty much being used every day now. I ordered the UHMW for the guides and I got the measuring marker from A1 place to get parts for things by the way. Thanks for looking. Todd

-- Allegheny Woodshop

26 comments so far

View Routerisstillmyname's profile


763 posts in 4797 days

#1 posted 06-29-2010 04:38 AM

Impressive upgrade for a contractor saw. Are you saying you built the fence and rails from scratch?That sure looks like Biesemeyer rails.

-- Router è ancora il mio nome.

View ToddE's profile


143 posts in 5222 days

#2 posted 06-29-2010 04:40 AM

Yeah, I got the steel and welded the fence up. The store models are way too pricey for me.
Honestly guys this was way easier to build than I first thought. It was nothing but a couple welds and bolting the square tubing to the angle iron. You don’t even need the back rail, I put it on for balance and for table mounting. I would say most of the strength was taken out of the back one though because I had to allow for the trunion adjustment lever on the Rigid 3612 saw and for the exterior upward swing of the motor mount.

-- Allegheny Woodshop

View BTKS's profile


1989 posts in 4752 days

#3 posted 06-29-2010 04:51 AM

Admirable talents in wood and metal. Great looking setup that should be a pleasure to use. BTKS

-- "Man's ingenuity has outrun his intelligence" (Joseph Wood Krutch)

View ToddE's profile


143 posts in 5222 days

#4 posted 06-29-2010 04:51 AM

Dave Price,
Hey I sent you those pictures you wanted. Hope they help. Sorry for the delay in posting this, have been pretty busy lately.

-- Allegheny Woodshop

View NormG's profile


6574 posts in 4292 days

#5 posted 06-29-2010 05:09 AM

Wonderful project

-- Norman - I never never make a mistake, I just change the design.

View Abbott's profile


2570 posts in 4591 days

#6 posted 06-29-2010 05:26 AM

Nice going Todd, it looks great.

-- Ohh mann...pancakes and boobies...I'll bet that's what Heaven is like! ♣ ♣ ♣ ♣

View Jerry's profile


221 posts in 4826 days

#7 posted 06-29-2010 05:38 AM

I love the TS additions.
Great Job!!

-- Jerry - Rochester, MN *Whether you think you can or you can't, you are probably right* - Henry Ford

View a1Jim's profile


118297 posts in 4865 days

#8 posted 06-29-2010 05:45 AM

A great job impressive.


View canadianchips's profile


2632 posts in 4285 days

#9 posted 06-29-2010 06:21 AM

Very nice large cutting area .

-- "My mission in life - make everyone smile !"

View Brandon's profile


4382 posts in 4239 days

#10 posted 06-29-2010 06:30 AM

Great work for sure! Where does that table end?

-- "hold fast to that which is good"

View zlatanv's profile


691 posts in 4522 days

#11 posted 06-29-2010 08:29 AM

Your going to need a bigger shop for that table, looks great!

-- Z, Rockwall, TX

View CampD's profile


1833 posts in 4774 days

#12 posted 06-29-2010 01:20 PM

Very nice upgrade.
and I might add thats a lot of flat surface

-- Doug...

View JimDaddyO's profile


679 posts in 4367 days

#13 posted 06-29-2010 02:01 PM

That’s awesome! Built my own fence too. Yours is a bit nicer…lol

-- my blog: my You Tube channel:

View efsavage's profile


26 posts in 4447 days

#14 posted 06-29-2010 03:03 PM

Your table is bigger than my shop!

View Ken90712's profile


18082 posts in 4476 days

#15 posted 06-29-2010 03:04 PM

If you get the Triton 2 1/2 router it can be mounter on a plate and raised and lowered from the top of table without a lift. You can also change bits without removing the router with one wrench from the top of table as well. Great router and great price! I love this thing. Here is some info on it.

-- Ken, "Everyday above ground is a good day!"

showing 1 through 15 of 26 comments

Have your say...

You must be signed in to post the comments.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics