LumberJocks

j_olsen's Favorites

  • Advertise with us
View mafe's profile

Drill press table and much more! #1: Making the table, fence, and shelf pin jig (my tour de table) Blog

08-20-2010 12:17 PM by mafe | 10 comments »

Making the table, fence, and shelf pin jig!This story are based on a real bench drillpress, all you see are reality, and all at your own risk… Ok some of you allready have seen my drillpress table, but since I like to shoot photo, and some more has come, I have finally finished my material for the blog (Some will say finally!!! This guy has writing fever, the truth are that I have been down with a throad infection, so I could not be in my shop). To my buddys, thank you for your patie...

Read this entry »


View dustbunny's profile

Tight Weave the Down and Dirty

08-08-2010 07:16 PM by dustbunny | 15 comments »

Several people asked me to blog the process of the tight weave board.The original tight weave board was posted by degoose here as a blog. Larry Rocks !! I don’t actually have one to be made from the start right now, so I pieced together what I have to try to illustrate the process. In some places you will have to use a little bit of imagination, but I think it will be clear. Okay, the key to the weave or the tight weave boards is-1. lumber should be square2. cuts must be accurate3...

Read this entry »


View dakremer's profile

How to Build a Sofa/Couch #1: Arm Rests

05-22-2010 11:59 PM by dakremer | 8 comments »

DISCLAIMER: Before I start this blog, I want to make sure everyone knows that I am NOT a professional sofa/furniture builder. I just took on this project because 1) I needed a sofa and 2) because I thought it’d be really fun and satisfying if I built my own sofa. This is all my own design, and besides looking at a few pics on the internet, this is all my OWN method of doing it. That being said – for any of you professional sofa builders out there, I am sorry if I’m not d...

Read this entry »


View poroskywood's profile

Drunken Cutting Boards #1: Drunken Alice in Wonderland Cutting Board

09-10-2009 03:22 AM by poroskywood | 52 comments »

Hey everybody, after a few personal messages here is my version of a how to on a Drunken Checker Board. I of coarse bow to the Chairman of the Board and pay tribute with beer. This is a Off-Checker pattern I call “Drunken Alice in Wonderland” The “serendipitous” nature of this piece is appealing in a far out sort of way. Here Goes… So first I prepare the Material. I am using Hard Maple and Walnut both are surfaced flat and cut 1” x 9” x 14&...

Read this entry »


View Mark A. DeCou's profile

A Scrimshaw Art Journey: What it is & How to Do it; Five Simple Steps to Success

11-11-2007 11:27 PM by Mark A. DeCou | 17 comments »

A Scrimshaw Art Journey: A Lumberjock’s “Short Version” of the Techniques for Decorating a Powder Horn by: Mark A. DeCouwww.decoustudio.com (This writing, photos, and artwork are protected by copyright by M.A. DeCou 2007-2010, all rights reserved, please ask permission before using any part or component.) =============================== UPDATE 9-25-2012:This past summer I had four students at the John C. Campbell Folk School class on Powder Horn Building and Scr...

Read this entry »


View degoose's profile

David's [aka Patron] double curve..my version of the jig? #1: Where to start? The Table!

06-10-2009 10:07 AM by degoose | 19 comments »

I have spent the last few days in the workshop working out how to make this jig.. and have it durable and repeatable and totally accurate and easy to use.Actually this jig can be used for two different projects … well probably more that two but thats all I have used it for so far.To start, I had to build a table to go over the bandsaw table for the jig to pivot on. [double pivot actually][two pivots two pics right!! ]The table was made from 5/8” [15mm] plywood, with silver ash us...

Read this entry »


View degoose's profile

Spirals #1: How to make the "Spiral Lazy Larry"

06-01-2009 06:52 AM by degoose | 23 comments »

You will need 12 pieces of timber roughly 5’’ by 12’’ whatever thickness you want. [ I milled mine to 5/8”]The first one I made was PH and SA—6 of each.Place timber in the jig and cut the first arc.Move the piece into the fence, clamp and make the second arc cut. Repeat 12 times.Glue it up and cut it into a circle.Put on a little tung oil finishThats about It.

Read this entry »


View degoose's profile

Glue up of a woven board..

05-17-2009 10:31 AM by degoose | 19 comments »

This is just a little tip.. not the whole tutorial of how to cut and make a woven board.Basically you all can make the weave with the two accent stripes on each side.. right.[ ok just a length of the main timber with 2 stripes cut 1/16 or 1/8 ” thick and glued up. see the pics and work it out ]You can also make the background pieces from the other of the accent timbers the same width as the main weave less the accents.. ok so far.. so I don’t need to go though all that do I? PM m...

Read this entry »


View degoose's profile

How to make a endgrain tumbling block butcher block board!

08-12-2009 12:13 PM by degoose | 57 comments »

Hi guys ,, I had a request to make a tutorial with regards the endgrain Tumbling Block Design.First off,.., You need to decide the size of the blocks…. for this example I used 1” stock… Or something similar.. actually just over .. once dressed. Set the blade of the table saw to 60 degrees.. a bevel box makes this simpleI use the INCRA fence system so it is easy to rip bevels off side of the blade.Once the bevels are ripped measure the length of the bevel and move the f...

Read this entry »



DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com