LumberJocks Woodworking Forums

  • Advertise with us
All Topics Replies Last post
View jayseedub's profile

Router Lift Into Sawstop Extension Table

06-17-2021 08:51 PM by jayseedub in Power Tools, Hardware and Accessories

I have the Sawstop Contractor Saw (CNS—not the Jobsite one) with the 36...

12 06-19-2021 11:29 PM
View Knockonit's profile

moving a jet 1642 lathe

06-14-2021 12:09 PM by Knockonit in Woodturning

I”m in process of buying a jet 1642 lathe and accessories, and accordin...

13 06-19-2021 10:57 PM
View Bearcontrare's profile

Stuip Simple Jury-rigged Outfeed Table

06-19-2021 09:39 PM by Bearcontrare in Focus on the Workspace

Finaaly got some time with Beloved Spouse away to get some things done. Been...

0 06-19-2021 09:39 PM
View OldBull's profile

I have looked everywhere, what is D shape sub base for on a palm router?

06-18-2021 04:25 PM by OldBull in Power Tools, Hardware and Accessories

I am going to buy a palm router and it is between the colt and dewalt 611. Wh...

19 06-19-2021 09:34 PM
View Njner's profile

Should hobbyist pricing undercut the professionals or not?

12-29-2020 03:39 PM by Njner in Sweating for Bucks Through Woodworking

Wanting to get some thoughts on pricing. I’m not looking for a typical...

57 06-19-2021 09:09 PM
View Bearcontrare's profile

Stupid Simple Jury-Rigged Outfeed Table

06-19-2021 09:07 PM by Bearcontrare in Jigs & Fixtures

Finally gotten time when Beloved Spouse is away from home to get some things ...

0 06-19-2021 09:07 PM
View nickbatz's profile

1/2" dovetail on large joint?

06-18-2021 08:30 PM by nickbatz in Joinery

Will the FBI come knocking if I use a 1/2” half blind dovetail jig on t...

9 06-19-2021 08:48 PM
View DBwoods's profile

Breadboard ends

06-19-2021 03:40 PM by DBwoods in Joinery

I’m making a bed from solid cherry. The footboard consists of a 16 inch...

2 06-19-2021 06:53 PM
View Belg1960's profile

Kumiko books?

06-16-2021 09:19 PM by Belg1960 in Woodworking Skill Share

Guys, I’m looking for a starter book which might bridge into a little m...

9 06-19-2021 06:12 PM
View Ralphw62's profile

Hi, I'm back after a few years..... I am looking for wood for my boat again.

06-16-2021 01:14 PM by Ralphw62 in Wood & Lumber

Hi, I’m back after a few years….. I am looking for wood for my bo...

5 06-19-2021 03:49 PM
View Woodyvolt's profile

Identifying Wood

06-16-2021 02:43 PM by Woodyvolt in Wood & Lumber

I recently obtained some lumber pieces that are considered exotic by the pers...

23 06-19-2021 11:41 AM
View Skrewd's profile

Reverse sliding table saw

06-18-2021 09:59 PM by Skrewd in Power Tools, Hardware and Accessories

Hello general question about something I can’t seem to find. Are all sliding ...

6 06-19-2021 10:41 AM
View SMP's profile

Delta TS at Lowes on clearance for $579

06-16-2021 02:30 AM by SMP in Power Tools, Hardware and Accessories

Just left Lowes and noticed the Delta TS had a yellow clearance label, $579 o...

13 06-19-2021 05:25 AM
View Phil32's profile

A Gift to All Model Car Builders

06-15-2021 08:28 PM by Phil32 in Woodworking Skill Share

Here is an example of the ultimate in model cars:

11 06-18-2021 11:06 PM
View Frankfort's profile

Anyone ever seen droplets of stain come out of oak grain?

06-18-2021 03:28 PM by Frankfort in Finishing

Anyone else ever seen stain or oil “squeeze” (for lack of better ...

7 06-18-2021 09:05 PM
View Bowd84's profile

Mitre Saw - Festool Kapex Vs. Omga

02-26-2018 01:34 PM by Bowd84 in Power Tools, Hardware and Accessories

So I know this is a little bit of apples vs oranges comparison but I’m ...

12 06-18-2021 08:51 PM
View moke's profile

Grinder Stand

06-15-2021 06:22 PM by moke in Power Tools, Hardware and Accessories

I have altogether too many grinders, but I am looking to add yet another. No...

10 06-18-2021 08:33 PM
View Knockonit's profile

dust fitting info

06-17-2021 11:34 PM by Knockonit in Power Tools, Hardware and Accessories

I’ve read about all the threads, and there is alot of them and very in...

9 06-18-2021 08:10 PM
View Karda's profile

easy squeeze epoxy bottles

06-17-2021 11:54 PM by Karda in Woodturning

Hi, i have some stick fast epoxy in bottle I also have week hands. In order t...

9 06-18-2021 07:03 PM
View BurlyBob's profile

I'm on the hunt!

04-30-2021 05:40 AM by BurlyBob in Woodworking Trade & Swap

Listen guys! I’m wanting to finish out my collection of Stanley hand p...

75 06-18-2021 05:26 PM

« prev 1 2 3 4 5 6 ... 5302 next »
106031 topics


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics